Considering a human handed control system for the dc motor speed control, if the resistance wire cut out too slowly, then the _____________(a) starting resistance would burn(b) field winding would burn(c) speed will rise steeply(d) any of the mentionedI had been asked this question in final exam.Question is taken from DC Motor Starting in section DC Motors of Electrical Machines

Considering a human handed control system for the dc motor speed contr

1.	Considering a human handed control system for the dc motor speed control, if the resistance wire cut out too slowly, then the _____________(a) starting resistance would burn(b) field winding would burn(c) speed will rise steeply(d) any of the mentionedI had been asked this question in final exam.Question is taken from DC Motor Starting in section DC Motors of Electrical Machines
Answer» Correct ANSWER is (a) starting resistance would burn To EXPLAIN I would SAY: Due to the slow cut off the resistance the current will be high for a LARGE amount of TIME and it will cause the machine to burn.

Discussion

No Comment Found

Related InterviewSolutions

A PMMDC motor has an armature resistance of 4.2 ohms. When 6 V supply is applied to motor it runs at 1215 rpm drawing 14.5 mA on no-load. The rotational losses is?(a) 86.1 mW(b) 86.1 W(c) 8.6 W(d) 8.6 mWI had been asked this question in examination.Asked question is from Permanent Magnet DC (PMDC) Motors topic in division DC Motors of Electrical Machines
PMMDC can only be armature controlled.(a) True(b) FalseI have been asked this question in an internship interview.This interesting question is from Permanent Magnet DC (PMDC) Motors in division DC Motors of Electrical Machines
How to manage run-away issue for dc shunt motor in industry?(a) By using PMDCmotor(b) By using constant field motors(c) This can not be avoided(d) None of the mentionedI had been asked this question by my school teacher while I was bunking the class.The question is from Permanent Magnet DC (PMDC) Motors in division DC Motors of Electrical Machines
Why does DC motor sometimes run too fast when under-loaded?(a) Due to weak field(b) Due to high line voltage(c) Due to brush-shifted to neutral(d) All of the mentionedThe question was posed to me in a job interview.This intriguing question originated from Speed Control of DC Motors topic in portion DC Motors of Electrical Machines
PMDC had no ________ excited machine.(a) electrically(b) magnetically(c) none of the mentioned(d) leastI have been asked this question during an online interview.This interesting question is from Permanent Magnet DC (PMDC) Motors in portion DC Motors of Electrical Machines
PMMDC offers ______ characteristics.(a) shunt(b) series(c) armature(d) cumulativeI had been asked this question in an interview.The question is from Permanent Magnet DC (PMDC) Motors topic in section DC Motors of Electrical Machines
PMMDC are smaller in size due to __________(a) ansence of field winding(b) presence of smaller field winding(c) present of magnets(d) Any of the mentionedI got this question by my college professor while I was bunking the class.My doubt is from Permanent Magnet DC (PMDC) Motors in chapter DC Motors of Electrical Machines
Which type of field winding required in PMMDC?(a) series winding(b) shunt winding(c) cumulative winding(d) none of the mentionedThis question was posed to me in class test.The above asked question is from Permanent Magnet DC (PMDC) Motors in portion DC Motors of Electrical Machines
Run-away for large DC machine is avoided by using _________(a) a turn or two of cumulative compounding(b) compensating winding(c) stablizer winding(d) all of the mentionedI have been asked this question in class test.This is a very interesting question from Speed Control of DC Motors topic in chapter DC Motors of Electrical Machines
The qualities aspired to obtain a good permanent magnet is/are ____________(a) high residual flux(b) low coercivity(c) high coercivity(d) high residual flux and high coercivityThis question was posed to me in examination.My question comes from Permanent Magnet DC (PMDC) Motors topic in portion DC Motors of Electrical Machines

Discussion

No Comment Found

Related InterviewSolutions

Reply to Comment