How can R1 be scaled?(a) by using a scale(b) by using an ohmmeter(c) by calibration(d) by using a galvanometerThe question was posed to me at a job interview.This key question is from Advantages and Limitations of Maxwell Bridge topic in section Measurement of Inductance and Capacitance of Electrical Measurements

How can R1 be scaled?(a) by using a scale(b) by using an ohmmeter(c) b

1.	How can R1 be scaled?(a) by using a scale(b) by using an ohmmeter(c) by calibration(d) by using a galvanometerThe question was posed to me at a job interview.This key question is from Advantages and Limitations of Maxwell Bridge topic in section Measurement of Inductance and Capacitance of Electrical Measurements
Answer» Right option is (c) by calibration For explanation I would SAY: The RESISTANCE R1 in a Maxwell inductance capacitance BRIDGE can be scaled through calibration. The value of the Quality factor Q can be read directly through calibration.

Discussion

No Comment Found

Related InterviewSolutions

Maxwell’s Inductance Capacitance Bridge is used for measuring ___________(a) Inductance(b) Capacitance(c) Frequency(d) Mutual InductanceThis question was posed to me in an interview for internship.I'd like to ask this question from Advanced Problems on Measurement of Inductance using AC Bridges topic in chapter Measurement of Inductance and Capacitance of Electrical Measurements
In Maxwell’s Bridge, as shown in the figure below, the values of the resistance R1 and inductance L1 of a coil are to be calculated after the bridge is balanced. The values are?(a) 375 Ω and 75 mH(b) 75 Ω and 150 mH(c) 37.5 Ω and 75 mH(d) 75 Ω and 75 mHThis question was addressed to me during a job interview.This intriguing question comes from Advanced Problems on Measurement of Inductance using AC Bridges in division Measurement of Inductance and Capacitance of Electrical Measurements
Hay’s Bridge is used for measuring __________(a) Resistance in the milliohm range(b) Low values of capacitance(c) Comparison of resistances which are nearly equal(d) The Inductance of a coil with a large time constantI got this question in an interview.The origin of the question is Advanced Problems on Measurement of Inductance using AC Bridges in portion Measurement of Inductance and Capacitance of Electrical Measurements
The Bridge shown in the below figure is ______________(a) Maxwell’s Bridge(b) Wien’s Bridge(c) Anderson’s Bridge(d) Hay’s BridgeThe question was posed to me at a job interview.My doubt stems from Advanced Problems on Measurement of Inductance using AC Bridges topic in chapter Measurement of Inductance and Capacitance of Electrical Measurements
What is the disadvantage of Maxwell Bridge?(a) Inductance cannot be measured over a wide range(b) Measurement is not independent of frequency(c) Number of components is large(d) Inductance can be measured over a wide rangeThe question was posed to me in a national level competition.My question is taken from Advanced Problems on Measurement of Inductance using AC Bridges in chapter Measurement of Inductance and Capacitance of Electrical Measurements
In Wein’s bridge, the output frequency is determined by __________(a) RLC combination(b) LC combination(c) RC combination(d) RL combinationThe question was posed to me by my college professor while I was bunking the class.The doubt is from Advanced Problems on Measurement of Inductance using AC Bridges in portion Measurement of Inductance and Capacitance of Electrical Measurements
In Maxwell’s capacitance bridge for calculating unknown inductance, the various values at balance are, R1 = 300 Ω, R2 = 700 Ω, R3 = 1500 Ω, C4 = 0.8 μF. Calculate R1, L1 and Q factor, if the frequency is 1100 Hz.(a) 240 Ω, 0.12 H, 3.14(b) 140 Ω, 0.168 H, 8.29(c) 140 Ω, 0.12 H, 5.92(d) 240 Ω, 0.36 H, 8.29I have been asked this question by my school principal while I was bunking the class.I would like to ask this question from Advanced Problems on Measurement of Inductance using AC Bridges in section Measurement of Inductance and Capacitance of Electrical Measurements
In the Owen’s bridge shown in below figure, Z1 = 200∠60°, Z2 = 400∠-90°, Z3 = 300∠0°, Z4 = 400∠30°. Then the _______(a) Bridge is balanced with given impedance values(b) Bridge can be balanced, if Z4 = 600∠60°(c) Bridge can be balanced, if Z3 = 400∠0°(d) Bridge cannot be balanced with the given configurationThis question was addressed to me in an internship interview.Enquiry is from Advanced Problems on Measurement of Inductance using AC Bridges in portion Measurement of Inductance and Capacitance of Electrical Measurements
Bridge is suitable for _________(a) coils with high Q values(b) coils with low Q values(c) coils with intermediate Q values(d) coils with very high Q valuesThis question was addressed to me in a national level competition.This is a very interesting question from Shielding and Grounding of Bridges topic in chapter Measurement of Inductance and Capacitance of Electrical Measurements
Wagner device is a ____________(a) capacitance bridge(b) resistance bridge(c) inductance bridge(d) impedance bridgeI had been asked this question in quiz.My question is from Shielding and Grounding of Bridges topic in chapter Measurement of Inductance and Capacitance of Electrical Measurements

Discussion

No Comment Found

Related InterviewSolutions

Reply to Comment