Thermal compensation can be provided in a Wheatstone bridge by ________(a) using more than one resistive sensor(b) making use of a heat sink(c) using cooling fans(d) immersing the circuit into a liquidThis question was posed to me in an interview.Enquiry is from Applications of Wheatstone Bridge in portion Measurement of Resistance of Electrical Measurements

Thermal compensation can be provided in a Wheatstone bridge by _______

1.	Thermal compensation can be provided in a Wheatstone bridge by ________(a) using more than one resistive sensor(b) making use of a heat sink(c) using cooling fans(d) immersing the circuit into a liquidThis question was posed to me in an interview.Enquiry is from Applications of Wheatstone Bridge in portion Measurement of Resistance of Electrical Measurements
Answer» Right choice is (a) USING more than ONE resistive sensor To explain I would say: By making USE of more than one resistive sensor within the four ARMS of a Wheatstone bridge we get a full bridge, half bridge or a QUARTER bridge setup with an automatic balancing effect.

Discussion

No Comment Found

Related InterviewSolutions

The simultaneous applications of signals x (t) and y (t) to the horizontal and vertical plates respectively, of an oscilloscope, produce a vertical figure of 8 displays. If P and Q are constants and x(t) = P sin (4t + 30), then y(t) is equal to _________(a) Q sin (4t -30)(b) Q sin (2t +15)(c) Q sin (8t +60)(d) Q sin (4t +30)The question was posed to me in an online quiz.The origin of the question is Advanced Miscellaneous Problems on Measurement of Resistance in chapter Measurement of Resistance of Electrical Measurements
A galvanometer with a full-scale current of 10 mA has a resistance of 1000 Ω. The multiplying power of a 100 Ω shunt with this galvanometer is?(a) 110(b) 100(c) 11(d) 10The question was asked during an interview for a job.Query is from Advanced Miscellaneous Problems on Measurement of Resistance in division Measurement of Resistance of Electrical Measurements
Resistance is measured by the voltmeter-ammeter method employing DC excitation and a voltmeter is connected directly across the unknown resistance. If the voltmeter and ammeter readings are subject to maximum possible errors of ±2.4 % and ±1% respectively, then the magnitude of the maximum possible percentage error in the value of resistance deduced from the measurement is?(a) 1.4 %(b) 1.7 %(c) 2.4 %(d) 3.4 %The question was asked during an internship interview.I'm obligated to ask this question of Advanced Miscellaneous Problems on Measurement of Resistance topic in section Measurement of Resistance of Electrical Measurements
A 100 μA ammeter has an internal resistance of 100 Ω. The range is to be extended to 500 μA. The shunt required is of resistance __________(a) 20.0 Ω(b) 22.22 Ω(c) 25.0 Ω(d) 50.0 ΩThe question was posed to me by my college director while I was bunking the class.My question is from Advanced Miscellaneous Problems on Measurement of Resistance in portion Measurement of Resistance of Electrical Measurements
A DC ammeter has a resistance of 0.1 Ω and its current range is 0-100 A. If the range is to be extended to 0-500 A, the meter requires which of the following shunt resistance?(a) 0.010 Ω(b) 0.011 Ω(c) 0.025 Ω(d) 1.0 ΩI have been asked this question during a job interview.The query is from Advanced Miscellaneous Problems on Measurement of Resistance in section Measurement of Resistance of Electrical Measurements
ADC ammeter is rated for 15 A, 250 V. The meter constant is 14.4 A-s/rev. The meter constant at rated voltage may be expressed as __________(a) 3750 rev/kW-h(b) 3600 rev/kW-h(c) 1000 rev/kW-h(d) 960 rev/kW-hThe question was posed to me in a national level competition.This is a very interesting question from Advanced Miscellaneous Problems on Measurement of Resistance in chapter Measurement of Resistance of Electrical Measurements
A 35 V DC supply is connected across a resistance in series with an unknown resistance R. a voltmeter having a resistance of 1.2 kΩ is connected across 600 Ω resistance and reads 5 V. The value of the known resistance is 600 Ω. The value of resistance R will be?(a) 120 Ω(b) 400 Ω(c) 1.8 kΩ(d) 2.4 kΩThis question was addressed to me in final exam.Question is from Advanced Miscellaneous Problems on Measurement of Resistance topic in section Measurement of Resistance of Electrical Measurements
A setup is used to measure resistance R. The ammeter and voltmeter resistance are 0.01 Ω and 2000 Ω respectively. Their readings are 2 A and 180 V respectively, giving a measured resistance of 90 Ω. The percentage error in the measurement is?(a) 2.25 %(b) 2.35 %(c) 4.5 %(d) 4.71 %This question was posed to me in quiz.Asked question is from Advanced Miscellaneous Problems on Measurement of Resistance in division Measurement of Resistance of Electrical Measurements
A 500 A, 50 Hz current transformer has a bar primary. The secondary burden is a pure resistance of 1 Ω and it draws a current of 5 A. If the magnetic core requires 250 Ampere-turn for magnetization, the percentage ratio error is __________(a) 10.56%(b) -10.56%(c) 11.80%(d) -11.80%I got this question in examination.This is a very interesting question from Advanced Problems on Error Analysis in Electrical Instruments topic in section Measurement of Resistance of Electrical Measurements
Ra and Rd are the opposite arms of a Wheatstone bridge as are Rc and Rb. The source voltage is applied across Ra and Rc. Then when the bridge is balanced which one of the following is true?(a) Ra = Rc Rd/Rb(b) Ra = Rb Rc/Rd(c) Ra = Rb Rd/Rc(d) Ra = Rb + Rc + RdThis question was addressed to me in an online quiz.My question is based upon Advanced Miscellaneous Problems on Measurement of Resistance in section Measurement of Resistance of Electrical Measurements

Discussion

No Comment Found

Related InterviewSolutions

Reply to Comment