Which of the following feed line uses the length of stub and L/W ratio to control the match?(a) Microstrip line feed(b) Coaxial feed(c) Aperture coupling(d) Proximity CouplingThe question was posed to me at a job interview.The question is from Feed Methods topic in chapter Slot & Microstrip Antenna of Antennas

Which of the following feed line uses the length of stub and L/W ratio

1.	Which of the following feed line uses the length of stub and L/W ratio to control the match?(a) Microstrip line feed(b) Coaxial feed(c) Aperture coupling(d) Proximity CouplingThe question was posed to me at a job interview.The question is from Feed Methods topic in chapter Slot & Microstrip Antenna of Antennas
Answer» Right ANSWER is (d) Proximity Coupling The best I can explain: In Proximity coupling, the length of stub and length to WIDTH ratio of patch controls the match. Microstrip line feed acts as an extent to patch and is connected to patch just like a conducting strip. In coaxial feed, inner conductor is attached to patch and outer conductor to GROUND plane. In APERTURE coupling, ground plane separates the different SUBSTRATES.

Discussion

No Comment Found

Related InterviewSolutions

Which of the following is the application of Microstrip antenna in a telemedicine industry?(a) Wireless Body Area Network(b) Detection of moving targets(c) Rectenna application(d) WiMaxI have been asked this question in my homework.The above asked question is from Applications in section Slot & Microstrip Antenna of Antennas
Which of the following is the disadvantage of Microstrip line feeding?(a) Spurious feed radiation increases with increase in substrate thickness(b) Spurious feed radiation decreases with increase in substrate thickness(c) There is no Bandwidth limit(d) Low spurious radiationThe question was posed to me in a job interview.My question comes from Feed Methods topic in division Slot & Microstrip Antenna of Antennas
Microstrip slot antennas are complementary to the Microstrip dipole antennas(a) True(b) FalseThe question was asked in a job interview.Question is taken from Types topic in section Slot & Microstrip Antenna of Antennas
In which of the following type of antenna a patch is created during fabrication?(a) Microstrip antenna(b) Horn antenna(c) Wire antenna(d) Lens antennaI had been asked this question at a job interview.Question is taken from Patch Types topic in division Slot & Microstrip Antenna of Antennas
Rectenna Application of Microstrip antenna converts _______________(a) Microwave energy to DC power(b) Microwave energy to AC power(c) Microwave energy to solar energy(d) Inductive to capacitiveI have been asked this question in homework.I need to ask this question from Applications topic in section Slot & Microstrip Antenna of Antennas
What is the impedance of 2- element slot antenna with single slot antenna resistance =500Ω?(a) 125Ω(b) 500Ω(c) 1000Ω(d) 250ΩThis question was addressed to me in a job interview.This interesting question is from Types in section Slot & Microstrip Antenna of Antennas
Which of the following is the disadvantage of the coaxial feeding?(a) Fabrication is very difficult(b) Low spurious radiation(c) Narrow Bandwidth(d) No generation of higher order modesI got this question during an internship interview.My doubt stems from Feed Methods in portion Slot & Microstrip Antenna of Antennas
Which of the following allows independent optimization of feed mechanism?(a) Microstrip line feed(b) Coaxial feed(c) Aperture coupling(d) Proximity CouplingI have been asked this question during an internship interview.This intriguing question originated from Feed Methods topic in portion Slot & Microstrip Antenna of Antennas
Which of the following type of slot antenna gives good end-fire radiation?(a) Annular slot antenna(b) Tapered slot antenna(c) All slot antennas gives good end-fire radiation(d) None of slot antenna gives good end-fire radiationThe question was asked during an interview for a job.Asked question is from Types topic in portion Slot & Microstrip Antenna of Antennas
Which of the following antenna is obtained by removing a small area of metal from an infinite ground plane?(a) Slot antenna(b) Plane reflector(c) Dipole(d) Yagi-UdaThe question was asked in a job interview.My query is from Types in division Slot & Microstrip Antenna of Antennas

Discussion

No Comment Found

Related InterviewSolutions

Reply to Comment