While manufacturing the concrete masonry bricks, the cement-aggregate ratio should not be thinner than __________(a) 1:6(b) 1:3(c) 3:4(d) 1:4The question was asked in a job interview.My question is taken from Composite Masonry in division Composite Masonry of Construction & Building Materials

While manufacturing the concrete masonry bricks, the cement-aggregate

1.	While manufacturing the concrete masonry bricks, the cement-aggregate ratio should not be thinner than __________(a) 1:6(b) 1:3(c) 3:4(d) 1:4The question was asked in a job interview.My question is taken from Composite Masonry in division Composite Masonry of Construction & Building Materials
Answer» Correct OPTION is (a) 1:6 To explain: While manufacturing the concrete masonry BRICKS, the cement-aggregate RATIO should not be thinner than 1:6. The aggregate should have a mixture with the proportion of fine aggregate being 60% and COARSE aggregate being 40%.

Discussion

No Comment Found

Related InterviewSolutions

Which of the following is used to embed the reinforcement?(a) Lime mortar(b) Cement concrete(c) Dense cement mortar(d) Slaked limeI got this question during an interview.The query is from Composite Masonry topic in portion Composite Masonry of Construction & Building Materials
The figure below represents __________(a) Exmet(b) Bricktor(c) Pile(d) PierThe question was asked at a job interview.The origin of the question is Composite Masonry in chapter Composite Masonry of Construction & Building Materials
Which of the following is not a type of structural clay unit in hollow clay blocks masonry?(a) Partition block(b) Fixing block(c) Load bearing block(d) Cavity blockI had been asked this question in homework.This interesting question is from Composite Masonry topic in section Composite Masonry of Construction & Building Materials
Reinforced brickwork is used in which of the following circumstances?(a) When the brick wall is to carry light loads(b) When the brickwork has to bear some shear stress(c) When it is needed to decrease the longitudinal bond(d) When the brickwork does not have to bear any shear stressI have been asked this question in my homework.My doubt stems from Composite Masonry topic in chapter Composite Masonry of Construction & Building Materials
In stone composite masonry, ashlar masonry is used in backing of the wall while rubble masonry is used in the facing.(a) True(b) FalseThe question was posed to me during a job interview.My enquiry is from Stone Composite Masonry topic in chapter Composite Masonry of Construction & Building Materials
Which of the following should be used for construction in brick-backed ashlar masonry?(a) Cement mortar(b) Lime mortar(c) Mud mortar(d) Cement concreteI had been asked this question during an interview for a job.The doubt is from Brick Stone Composite Masonry topic in division Composite Masonry of Construction & Building Materials
In hollow clay blocks masonry, all the blocks should be dipped in _________ before using them.(a) Alcohol(b) Acetone(c) Water(d) EtheneThis question was posed to me in class test.The question is from Composite Masonry topic in section Composite Masonry of Construction & Building Materials
In concrete masonry, hollow concrete units are used for _________ walls.(a) Either load-bearing or non-load bearing(b) Only load-bearing(c) Only non-load bearing(d) Neither load-bearing nor non-load bearingThis question was posed to me in a job interview.My question is from Composite Masonry in section Composite Masonry of Construction & Building Materials
Solid concrete blocks are obtained from lightweight aggregates while hollow concrete blocks are obtained from heavy aggregates.(a) True(b) FalseThis question was addressed to me in semester exam.Origin of the question is Composite Masonry topic in chapter Composite Masonry of Construction & Building Materials
In concrete masonry, a hollow concrete block has core-void area greater than __________ of the gross area.(a) 20%(b) 15%(c) 30%(d) 25%I had been asked this question in exam.The above asked question is from Stone Composite Masonry topic in division Composite Masonry of Construction & Building Materials

While manufacturing the concrete masonry bricks, the cement-aggregate ratio should not be thinner than __________(a) 1:6(b) 1:3(c) 3:4(d) 1:4The question was asked in a job interview.My question is taken from Composite Masonry in division Composite Masonry of Construction & Building Materials

Discussion

No Comment Found

Related InterviewSolutions

Reply to Comment