Explore topic-wise InterviewSolutions in .

This section includes InterviewSolutions, each offering curated multiple-choice questions to sharpen your knowledge and support exam preparation. Choose a topic below to get started.

1.

Sleepers (ties) are mostly made up of _______________(a) wood(b) prestressed concrete(c) metal(d) steakI had been asked this question in my homework.Enquiry is from Railway Line topic in division Road Estimating, Sanitary and Water Supply Work of Civil Engineering Drawing

Answer»

Right choice is (b) prestressed concrete

Easiest explanation: Prestressed concrete is a FORM of concrete used in construction which is “pre-stressed” by being placed under compression prior to SUPPORTING any loads beyond its own dead WEIGHT. This compression is produced by the tensioning of high-strength “tendons” located within or adjacent to the concrete volume and is done to improve the PERFORMANCE of the concrete in service.

2.

Normally earthwork is estimated for 30 m lead for distance and 1.5 m lift for height or depth, and this distance of 30 m and the height of 1.5 m are known as _____________(a) vertical lead and lift(b) normal lead and lift(c) horizontal lead and lift(d) transverse lead and liftI had been asked this question in final exam.My question comes from Estimate of Earthwork by Three Methods in section Road Estimating, Sanitary and Water Supply Work of Civil Engineering Drawing

Answer»

Right OPTION is (b) normal lead and LIFT

To explain I would say: Normal rate for earthwork is for 30 m lead and 1.5 m lift. For greater lead or lift the rates will be different (higher) for every unit of 30 m lead and for every unit of 1.5 m lift. The earthwork is, THEREFORE, estimated SEPARATELY for every 30 m lead and for every 1.5 m lift.

3.

____________ is the predominant gauge used by Indian railways.(a) Broad gauge(b) Narrow gauge(c) Metre gauge(d) Standard gaugeThis question was addressed to me by my college professor while I was bunking the class.I need to ask this question from Railway Line in section Road Estimating, Sanitary and Water Supply Work of Civil Engineering Drawing

Answer»

The correct OPTION is (a) BROAD gauge

Easy explanation: INDIAN gauge 1,676 mm (5 FT 6 in) (a broad gauge) is the predominant gauge USED by IR.

Broad Gauge: width 1676 mm to 1524 mm or 5’6” to 5’0”

Standard Gauge: width 1435 mm and 1451 mm or 4′-8⅟2”

Metre Gauge: width 1067 mm, 1000 mm and 915 mm or 3′-6”, 3′-33/8” and 3′-0”

Narrow Gauge: width 762 mm and 610 mm or 2′-6” and 2′-0”.

4.

Name the open drains provided for conveying water from kitchens, bathroom and rain water to main sewers.(a) drains(b) Sewers(c) Soak pit(d) Surface drainsThis question was posed to me during an online exam.My question comes from Water Supply Works in portion Road Estimating, Sanitary and Water Supply Work of Civil Engineering Drawing

Answer»

Right ANSWER is (d) Surface drains

To explain I would SAY: These are usually provided at the side of the road and along the boundary line of the BUILDING. As far as possible drains should not be laid under the buildings. For efficient draining the surfacedrains should have certain qualities, such as should be laid in such a gradient to develop self -cleaning velocity, should have a reasonable free board at the top, joint should be smooth FINISHED, easy curves, INNER surface should be smooth, cheap in construction and maintenance.

5.

The lowest or weakest level of decontamination is sanitation.(a) True(b) FalseThe question was posed to me in class test.This interesting question is from Sanitary Works topic in section Road Estimating, Sanitary and Water Supply Work of Civil Engineering Drawing

Answer»

Right option is (b) False

To explain: The strongest LEVEL of DECONTAMINATION in increasing order is: Sanitation, Antiseptic, Disinfection, STERILIZATION.

6.

What is the longitudinal slope called?(a) Kerb(b) Horizon(c) Grade(d) LiftThis question was posed to me in an internship interview.This is a very interesting question from Estimate of Earthwork by Three Methods topic in division Road Estimating, Sanitary and Water Supply Work of Civil Engineering Drawing

Answer»

Right OPTION is (c) Grade

To explain I WOULD SAY: The grade (also called slope, incline, gradient, mainfall, pitch or rise) of a PHYSICAL feature, landform or constructed line refers to the tangent of the angle of that surface to the horizontal. It is a special case of the slope, where ZERO indicates horizontality. A larger number indicates higher or steeper degree of “tilt”. Often slope is calculated as a ratio of “rise” to “run”, or as a fraction (“rise over run”) in which run is the horizontal distance and rise is the vertical distance.

7.

Figure shown below represents a symbol ‘A’, it signifies?(a) Septic tank(b) Soak pit(c) Gutter(d) Water storing tankI have been asked this question in my homework.Question is from Design of Septic Tanks topic in portion Road Estimating, Sanitary and Water Supply Work of Civil Engineering Drawing

Answer»

The correct option is (a) SEPTIC tank

Easiest explanation: A septic tank collects and treats wastewater at a property that is not connected to the mains sewer system. Installed underground, a septic tank makes use of NATURAL processes to treat the sewage it stores. Usually made up of TWO chambers or compartments, the tank receives wastewater from an inlet pipe. Wastewater ENTERS the first CHAMBER and separates over time, with solids settling at the bottom, oils and greases forming a layer of scum at the top, and a layer of relatively clear water remaining in the middle.

8.

As a very general guideline it is recommended that the bottom of the pit should be at least _______ above groundwater level.(a) 0.5 m(b) 2 m(c) 12 m(d) 20 mI have been asked this question in an interview for internship.Question is taken from Design of Septic Tanks topic in section Road Estimating, Sanitary and Water Supply Work of Civil Engineering Drawing

Answer»

Correct option is (b) 2 m

Best explanation: As a very general GUIDELINE it is recommended that the bottom of the pit should be at least 2 m above GROUNDWATER level, and a MINIMUM horizontal distance of 30 m between a pit and a water source is normally recommended to limit exposure to MICROBIAL contamination.[1]However, no general statement should be made regarding the minimum lateral separation distances required to prevent contamination of a well from a pit latrine. For example, even 50 m lateral separation distance might not be sufficient in a strongly karstified system with a down gradient supply well or spring, while 10 m lateral separation distance is completely sufficient if there is a well developed clay cover layer and the annular space of the groundwater well is well sealed.

9.

The surface of the head of each of the two rails can be maintained by using a ___________(a) rail header(b) rail trimmer(c) rail grinder(d) rail cutterI had been asked this question in homework.I need to ask this question from Railway Line topic in section Road Estimating, Sanitary and Water Supply Work of Civil Engineering Drawing

Answer»

The correct choice is (c) rail GRINDER

The best I can explain: A rail grinder (or rail grinder) is a maintenance of WAY vehicle or train used to restore the profile and remove irregularities from worn tracks to extend its life and to improve the ride of trains using the TRACK. Rail grinders were developed to increase the lifespan of the tracks being serviced for rail corrugation. Rail grinding is a process that is done to stop the deformation due to use and FRICTION on railroad tracks by REMOVING deformations and corrosion.

10.

In office building what is the requirement of a water closet for 50 persons?(a) 4(b) 5(c) 2(d) 1I have been asked this question in an online interview.This interesting question is from Water Supply Works in division Road Estimating, Sanitary and Water Supply Work of Civil Engineering Drawing

Answer» RIGHT answer is (c) 2

The explanation: In OFFICE building the requirement of a water closet for 25 people or PART THEREOF, 1 closet is required.
11.

__________ is the highest form of decontamination.(a) Sterilization(b) Sanitation(c) Disinfection(d) HygieneI have been asked this question by my school principal while I was bunking the class.Origin of the question is Sanitary Works in division Road Estimating, Sanitary and Water Supply Work of Civil Engineering Drawing

Answer»

Right choice is (a) Sterilization

To explain I would say: The process of RENDERING an article safe to handle, by cleaning with or without DISINFECTION or sterilization. Disinfection: The process of killing or removing pathogenic micro-organisms, except for bacterial SPORES and prions from INANIMATE objects or skin, to a LEVEL which is not harmful to health.

12.

The shape of ballast should be _____________(a) triangular(b) irregular(c) spherical(d) longitudinalThis question was addressed to me at a job interview.My question comes from Railway Line in portion Road Estimating, Sanitary and Water Supply Work of Civil Engineering Drawing

Answer» CORRECT option is (b) irregular

For explanation: Stones must be irregularly cut, with sharp edges, so that they properly interlock and GRIP the ties in order to fully secure them against movement; spherical stones cannot do this. In order to let the stones fully settle and interlock, SPEED limits are often LOWERED on sections of track for a period of time after NEW ballast has been laid.
13.

A raised edge at the side of the roadway is known as _____________(a) curb(b) curvature(c) inclination(d) circularI got this question by my college director while I was bunking the class.My question is from Estimate of Earthwork by Three Methods topic in section Road Estimating, Sanitary and Water Supply Work of Civil Engineering Drawing

Answer»

The CORRECT ANSWER is (a) curb

Best explanation: A curb or kerb is the edge where a raised sidewalk (pavement in BRITISH ENGLISH) or road median/central RESERVATION meets a street or other roadway.

14.

To calculate the volume of earthwork from contour plan for filling a depression or pond and for cutting a hillock __________________ may be used conveniently.(a) elevation method(b) section area method(c) prismoidal formula(d) contour methodI have been asked this question in semester exam.This question is from Estimate of Earthwork by Three Methods topic in section Road Estimating, Sanitary and Water Supply Work of Civil Engineering Drawing

Answer»

The correct option is (c) prismoidal formula

The best explanation: The area with every contour may be found by using a Planimeter or a tracing paper containing squares. Then the prismoidal formula may be APPLIED to calculate the volume, the DISTANCE between the TWO SECTIONS will be the contour INTERVALS, i.e., the difference of level between two consecutive contours.

15.

For 1 wash Basin how many persons are allowed to use it at a time at office buildings?(a) 45(b) 35(c) 25(d) 15The question was asked by my college director while I was bunking the class.I would like to ask this question from Water Supply Works in chapter Road Estimating, Sanitary and Water Supply Work of Civil Engineering Drawing

Answer»

The correct answer is (c) 25

The best I can explain: In Cinema and theatres 1 for 200 persons or part thereof, in restaurant 1 for every WATER CLOSET provision, in hostels 1 for 8 persons or part thereof.

16.

______ percentage of Indian rails routes are electrified.(a) 66%(b) 25%(c) 45%(d) 76%The question was posed to me in an international level competition.Asked question is from Railway Line in portion Road Estimating, Sanitary and Water Supply Work of Civil Engineering Drawing

Answer»

Right choice is (c) 45%

To explain: It is the fourth largest railway network in the world by size, comprising 119,630 kilometres (74,330 mi) of total track and 92,081 km (57,216 mi) of running track over a route of 66,687 km (41,437 mi) at the end of 2015-16. Forty-five percentage of its routes are electrified, USING entirely 25 kV AC electric traction. The track is mostly broad gauge with small STRETCHES of metre and narrow gauge track. 37% of the tracks are double or multiple TRACKED.

17.

The _______ are used for preventing foul gas from sewers to back flow in the house.(a) air freshners(b) traps(c) naphthalene balls(d) phenylI got this question in an online quiz.The origin of the question is Water Supply Works in portion Road Estimating, Sanitary and Water Supply Work of Civil Engineering Drawing

Answer»

The correct answer is (b) traps

Explanation: In plumbing, a trap is a DEVICE which has a shape that uses a bending path to capture WATER to prevent sewer gases from entering buildings, while allowing waste to pass through. In REFINERY APPLICATIONS, traps are used to prevent hydrocarbons and other dangerous gases from escaping outside through drains.

18.

In _________________ system the source of supply is lake or impounding reservoir at some elevation.(a) parallel(b) gravity distribution(c) pumps distribution(d) rain distributionI got this question during an interview.The origin of the question is Water Supply Works in section Road Estimating, Sanitary and Water Supply Work of Civil Engineering Drawing

Answer»

Correct choice is (b) gravity distribution

The best I can explain: This system is possible when the SOURCE of supply is lake or impounding RESERVOIR at some ELEVATION above the city so that sufficient PRESSURE can be MAINTAINED in the mains.

19.

The distance shown by red line represents ______________(a) separation(b) parallel way(c) height(d) gaugeThe question was posed to me during an online interview.The above asked question is from Railway Line topic in division Road Estimating, Sanitary and Water Supply Work of Civil Engineering Drawing

Answer» RIGHT option is (d) gauge

To elaborate: During the early days of rail, there was considerable VARIATION in the gauge used by different systems. TODAY, 54.8% of the world’s railways use a gauge of 1,435 mm (4 ft 8 \(\frac{1}{2}\) in), known as standard or international gauge. Gauges wider than standard gauge are called broad gauge; narrower, narrow gauge. Some stretches of TRACK are dual gauge, with THREE (or sometimes four) parallel rails in place of the usual two, to allow trains of two different gauges to use the same track.
20.

_____________ curves are curves which, when viewed from the side, are concave upwards. This includes vertical curves at valley bottoms, but it also includes locations where an uphill grade becomes steeper, or a downhill grade becomes less steep.(a) Sag horizontal(b) Hog horizontal(c) Sag vertical(d) Hog verticalThis question was addressed to me in a job interview.My question is from Estimate of Metalled Roads topic in division Road Estimating, Sanitary and Water Supply Work of Civil Engineering Drawing

Answer»

Right answer is (c) Sag vertical

Explanation: The most important design criterion for these curves is HEADLIGHT SIGHT DISTANCE. When a driver is driving on a sag curve at night, the sight distance is limited by the higher grade in front of the vehicle. This distance must be long enough that the driver can see any obstruction on the road and stop the vehicle within the headlight sight distance. The headlight sight distance (S) is DETERMINED by the ANGLE of the headlight and angle of the tangent slope at the end of the curve.

21.

Calculate the quantity of cement concrete for cement concreting one kilometre length of 3.70 m wide road for an 8 cm thick layer. Also calculate cost at the rate of Rs.375.00 per cu m.(a) Rs.134440.00(b) Rs.191000.00(c) Rs.111000.00(d) Rs.211000.00The question was posed to me during an interview for a job.The origin of the question is Estimate of Metalled Roads in portion Road Estimating, Sanitary and Water Supply Work of Civil Engineering Drawing

Answer» RIGHT choice is (C) Rs.111000.00

For explanation I WOULD say: Quantity of CEMENT concrete = 1000*3.70*0.80 = 296 cu m

Cost per kilometre of road = 296*375.00 = Rs.111000.00.
22.

Symbol shown below represents ______________ type of road signal.(a) disabled people(b) crossing area(c) men at work(d) garbage areaThe question was posed to me in unit test.The question is from Estimate of Metalled Roads topic in portion Road Estimating, Sanitary and Water Supply Work of Civil Engineering Drawing

Answer»

The correct option is (c) men at work

To explain: Men At Work Sign is MUTCD compliant for SAFETY protocol and compliance on roadways and in parking lots. A Men At Work Sign is a useful device to help display OFFICIAL REGULATIONS and provide mandatory information to drivers and pedestrians on both public and private roadways and parking areas.

23.

Designated point on a road where road marking or other means helps pedestrians cross safely is called?(a) Zebra crossing(b) Pedestrian crossing(c) Footpath(d) SubwayThis question was addressed to me in an online interview.The query is from Estimate of Earthwork by Three Methods in chapter Road Estimating, Sanitary and Water Supply Work of Civil Engineering Drawing

Answer»

The correct option is (b) Pedestrian crossing

The best I can explain: A pedestrian crossing or crosswalk is a place designated for pedestrians to CROSS a road. Crosswalks are designed to keep pedestrians together where they can be seen by motorists, and where they can cross most safely across the flow of vehicular traffic.

Marked pedestrian crossings are often found at intersections, but MAY also be at other points on busy roads that would otherwise be too unsafe to cross without assistance due to vehicle numbers, SPEED or road widths. They are also COMMONLY installed where large numbers of pedestrians are attempting to cross (such as in shopping areas) or where vulnerable road users (such as school children) regularly cross.

24.

90% of urban water supply and sanitation services are currently in the ______________(a) industry(b) agriculture(c) government(d) public sectorI have been asked this question in an interview for internship.This question is from Water Supply Works topic in division Road Estimating, Sanitary and Water Supply Work of Civil Engineering Drawing

Answer»

Right CHOICE is (d) public sector

To elaborate: They are owned by the state or local authorities, or also by collectives or cooperatives. They run without an aim for profit but are based on the ethos of providing a common good considered to be of public INTEREST. In most middle and low-income countries, these PUBLICLY owned and managed water PROVIDERS can be inefficient as a result of political INTERFERENCE, leading to over-staffing and low labour productivity.

25.

Connecting pipe should be _______ mm minimum diameter.(a) 60(b) 300(c) 700(d) 100This question was addressed to me in an online quiz.My question comes from Design of Septic Tanks in section Road Estimating, Sanitary and Water Supply Work of Civil Engineering Drawing

Answer»

The correct ANSWER is (a) 60

To explain: It may be of R.C.C, Hume pipe, cast iron pipe, S.W. Inlet and OUTLET may be made through T-junction pipe or baffle wall of precast R.C.C. may be provided at a distance 1/5 of length of the SEPTIC tank so that the inlet sewage may not disturb the working of the tank.

26.

Find the area of permanent land required for a State Highway for one kilometre length, the width of permanent land being 30 m.(a) 0.5 hectare(b) 3 hectare(c) 4 hectare(d) 6 hectareThis question was addressed to me in an interview for internship.This interesting question is from Estimate of Metalled Roads in section Road Estimating, Sanitary and Water Supply Work of Civil Engineering Drawing

Answer»

The correct CHOICE is (B) 3 HECTARE

For EXPLANATION: Permanent land = 1000 *300 = 30000 sq m = 30000/10000 = 3 hectare.

27.

Metalling of road usually consists of ______ layers of coats.(a) 5(b) 3(c) 2(d) 6This question was addressed to me in final exam.My question comes from Estimate of Metalled Roads topic in section Road Estimating, Sanitary and Water Supply Work of Civil Engineering Drawing

Answer»

Correct choice is (b) 3

Easiest explanation: The soiling coat, inter coat and top coat. The metal may be stone ballast, brick ballast, KANKAR, etc. The inter coat and top coat are made with 12 cm (4 1/2 ”) THICK layer loose compacted to 8 cm (3”). The soiling coat may be of brick flat or brick on edge, or of stone boulder or of same type as for the inter or top coat if the sub-soil is GOOD, or may be of greater.The top or wearing coat may also be of cement CONCRETE bituminous.

28.

The size of the faeces drop hole in the floor or slab should not be larger than ____________(a) 5m(b) 25 cm(c) 45 cm(d) 250 mmI had been asked this question in homework.My question is from Design of Septic Tanks in chapter Road Estimating, Sanitary and Water Supply Work of Civil Engineering Drawing

Answer»

Right answer is (b) 25 cm

To explain: The user positions themself over the small drop hole during use. The size of the feces drop hole in the floor or slab should not be larger than 25 CENTIMETERS (9.8 inches) to prevent children FALLING in. Light should be PREVENTED from entering the pit to reduce access by flies. This REQUIRES the use of a lid to cover the hole in the floor when not in use. However, in practice, such a lid is not commonly used as it is easy to lose it or for the lid to get very filthy.

29.

A road junction where typically three or more roads are joined by a circular section of road is called _________(a) intersection(b) merging(c) circulation(d) roundaboutI have been asked this question in final exam.I need to ask this question from Estimate of Metalled Roads in portion Road Estimating, Sanitary and Water Supply Work of Civil Engineering Drawing

Answer»

The correct answer is (d) roundabout

The best I can explain: A roundabout, also called a TRAFFIC circle, road circle, rotary, rotunda or island, is a type of circular intersection or JUNCTION in which road traffic FLOWS almost continuously in one direction around a central island.

So-called “MODERN” roundabouts require ENTERING traffic to give way to traffic already in the circle and optimally observe various design rules to increase safety.

30.

Find the area of temporary land required for one kilometre length of a road from the following data.(a) 32.50 m(b) 76.89 m(c) 39.50 m(d) 45.50 mThis question was posed to me in an online interview.Asked question is from Estimate of Metalled Roads in division Road Estimating, Sanitary and Water Supply Work of Civil Engineering Drawing

Answer» RIGHT ANSWER is (a) 32.50 m

Easy explanation: Quantity of EARTHWORK in embankment = (Bd+sd2)*length = (10*1.5+2*1.52)*1000=19.5*1000=19500

Area of temporary in embankment land=(19500)/(depth of borrowpit)=19500/0.30=65000 sq m

65000/10000=6.5 hectare

Width of temporary land = Area /Length = 65000 sq m/10000 = 65 m

Width of temporary land on either side = 65/2 = 32.50 m.
31.

Cross-section of earthwork of road in banking is in the form of trapezium. Name the method to calculate the quantity of earthwork.(a) Longitudinal formula(b) Quadrilateral formula(c) Prismoidal formula(d) Trapezium formulaI had been asked this question during an interview.My doubt is from Estimate of Earthwork by Three Methods topic in portion Road Estimating, Sanitary and Water Supply Work of Civil Engineering Drawing

Answer»

The correct ANSWER is (c) Prismoidal formula

To EXPLAIN I would say: QUANTITY or volume = L/6 (A1+A2+4Am).

32.

As of 2013 pit latrines are used by an estimated ____________ people.(a) 1.77 billion(b) 2.77 million(c) 1.77 billion(d) 4.66 billionThis question was posed to me in final exam.My doubt stems from Design of Septic Tanks topic in section Road Estimating, Sanitary and Water Supply Work of Civil Engineering Drawing

Answer»

Correct OPTION is (c) 1.77 BILLION

The explanation: This is mostly in the developing world as well as in rural and wilderness areas. In 2011 about 2.5 billion people did not have access to a proper toilet and one billion resort to open defecation in their surroundings. Southern Asia and Sub-Saharan AFRICA have the poorest access to toilets. In developing countries the cost of a simple pit toilet is typically between 25 and 60 USD. Ongoing maintenance costs are between 1.5 and 4 USD per PERSON per year which are often not taken into consideration.

33.

Anti-siphonage pipe is connected to _____________(a) top of P trap W.C.(b) main soil pipe(c) bottom of P trap W.C.(d) side of water closetThe question was asked in an interview for internship.The origin of the question is Sanitary Works in division Road Estimating, Sanitary and Water Supply Work of Civil Engineering Drawing

Answer»

Right choice is (c) bottom of P trap W.C.

To explain: A vent is open at top and bottom, to facilitate exit of foul gases. It is carried at least one meter higher than the ROOF level. RAIN water pipe: it is a pipe which carries only the rain water. Anti-siphonage pipe: it is pipe which is installed in the house drainage to PRESERVE the water SEAL of traps.

34.

The track and ballast form the ______________(a) Temporary way(b) True way(c) Rigid way(d) Permanent wayI had been asked this question in class test.I'd like to ask this question from Railway Line topic in chapter Road Estimating, Sanitary and Water Supply Work of Civil Engineering Drawing

Answer»

Right answer is (d) Permanent way

To explain: The permanent way is the ELEMENTS of railway lines: generally the pairs of rails typically laid on the sleepers (“ties” in AMERICAN parlance) embedded in ballast, intended to carry the ordinary TRAINS of a railway. It is described as permanent way because in the earlier days of railway construction, contractors often laid a TEMPORARY track to transport spoil and materials about the site; when this work was substantially COMPLETED, the temporary track was taken up and the permanent way installed.

35.

Below symbols refer to ____________(a) additional signs(b) cautionary sign(c) mandatory sign(d) informative signThe question was posed to me by my school principal while I was bunking the class.My question is based upon Estimate of Metalled Roads topic in portion Road Estimating, Sanitary and Water Supply Work of Civil Engineering Drawing

Answer»

Correct CHOICE is (c) mandatory sign

For explanation: Mandatory signs are road signs which are USED to set the obligations of all traffic which use a specific area of road. Unlike prohibitory signs, mandatory signs tell traffic what it MUST do, rather than must not do. Most mandatory road signs are CIRCULAR, may use white symbols on a blue background with white border or black symbols on a white background with a red border, although the latter is also ASSOCIATED with prohibitory signs.

36.

Calculate the quantity of metal required for a 3.70m wide Macadam road for one kilometre length for one layer of 8 cm compacted thickness.(a) 444 cu m(b) 565 cu m(c) 454 cu m(d) 765 cu mI got this question in my homework.My query is from Estimate of Metalled Roads in section Road Estimating, Sanitary and Water Supply Work of Civil Engineering Drawing

Answer»

Correct choice is (a) 444 cu m

For EXPLANATION: Quantity of METAL (loose) = 1000 m*3.70m*12 CM = 1000*3.70*.12=444 cu m

Volume of loose metal gets reduced 1/3 on COMPACTION.

37.

Typical lane widths range from ______ metres to _____ metres.(a) 1, 2.4(b) 10, 12.6(c) 3, 3.6(d) 8, 8.6I got this question in an interview for job.My doubt stems from Estimate of Earthwork by Three Methods in chapter Road Estimating, Sanitary and Water Supply Work of Civil Engineering Drawing

Answer»

Correct ANSWER is (c) 3, 3.6

Explanation: WIDER lanes and shoulders are usually used on roads with higher speed and higher volume traffic, and significant numbers of trucks and other large vehicles. Narrower lanes may be used on roads with lower speed or lower volume traffic.

Narrow lanes cost less to build and maintain, but also reduce the capacity of a ROAD to convey traffic. On rural roads, narrow lanes are likely to experience higher rates of run-off-road and head-on collisions. Wider roads increase the time needed to walk across and increase STORM water runoff.

38.

Soak pit shall not be less than ____________(a) 45 cm(b) 90 cm(c) 50 cm(d) 100 cmI got this question in final exam.I would like to ask this question from Design of Septic Tanks in chapter Road Estimating, Sanitary and Water Supply Work of Civil Engineering Drawing

Answer»

Right option is (b) 90 cm

Easy explanation: SOAK pit shall not be less than 90 cm in diameter and not less than 1.5 m in depth below invert level of the inlet pipe. The pit is constructed with lining of dry brick or stone with OPEN JOINTS backed with at LEAST 7.5 cm THICK coarse aggregate.

39.

The diameter of a domestic sewer pipe laid at gradient 1 in 100 is recommended ________(a) 100 mm(b) 150 mm(c) 210 mm(d) 400 mmI have been asked this question by my school teacher while I was bunking the class.Question is from Sanitary Works in section Road Estimating, Sanitary and Water Supply Work of Civil Engineering Drawing

Answer»

The correct option is (B) 150 mm

Easiest explanation: A sanitary sewer or “foul sewer” is an underground carriage system specifically for transporting sewage from houses and commercial buildings through pipes to treatment FACILITIES or DISPOSAL. Sanitary SEWERS are part of an overall system called a sewage system or sewerage.

Sewage may be treated to control water pollution before discharge to surface waters. Sanitary sewers serving industrial areas also carry industrial wastewater.

40.

Sanitary plumbing includes the installation of appliances such as dishwashers and washing machines; the replacement or repair of taps, ball valves and plugs.(a) True(b) FalseI got this question during an online exam.I'm obligated to ask this question of Sanitary Works topic in chapter Road Estimating, Sanitary and Water Supply Work of Civil Engineering Drawing

Answer»

The correct option is (B) False

The BEST EXPLANATION: Sanitary plumbing does not includes the installation of appliances such as DISHWASHERS and washing machines; the replacement or repair of taps, ball VALVES and plugs.

41.

In this form of track, the rails are welded together by utilising flash butt welding to form one continuous rail that may be several kilometres long, this type of rail is called __________(a) Continuous jointed rail(b) Merged rail(c) Continuous welded rail(d) Continuous welded railThis question was addressed to me during an internship interview.I need to ask this question from Railway Line in division Road Estimating, Sanitary and Water Supply Work of Civil Engineering Drawing

Answer»

Right choice is (c) Continuous WELDED rail

To explain I would say: In this form of track, the rails are welded together by utilising flash butt WELDING to form one continuous rail that may be several kilometres LONG. Because there are few joints, this form of track is very strong, gives a smooth RIDE, and needs less maintenance; trains can travel on it at higher speeds and with less friction. Welded rails are more expensive to lay than jointed tracks, but have much lower maintenance costs.

42.

Number of urinals required in hostels for 25 persons.(a) 5(b) 1(c) 5(d) 10The question was asked by my school teacher while I was bunking the class.My question is from Water Supply Works topic in section Road Estimating, Sanitary and Water Supply Work of Civil Engineering Drawing

Answer»

Correct OPTION is (b) 1

The BEST I can explain: In office building- 1 per persons, 2 per 21-45, 3 per 46-70 persons, 4 per 71-100. In cinema 1 for 25 persons or part thereof. In RESTAURANT 1 per 50 seats.

43.

Septic tank is usually consists of brick wall in cement not less than _______(a) 20 cm(b) 100 cm(c) 80 cm(d) 200 cmThis question was addressed to me by my college professor while I was bunking the class.The doubt is from Design of Septic Tanks topic in division Road Estimating, Sanitary and Water Supply Work of Civil Engineering Drawing

Answer» RIGHT choice is (a) 20 cm

The best EXPLANATION: Septic TANK is usually consists of BRICK wall in cement not less than 20cm(9”) thick and the foundation floor are of cement concrete 1:3:6 or 1:2:4. Both inside and outside faces of wall and floor are PLASTERED with a minimum thickness of 12mm thick cement mortar 1:3 and all inside corners are rounded.
44.

A ________ is a thoroughfare, route, or way on land between two places that has been paved or otherwise improved to allow travel by foot or some form of conveyance, including a motor vehicle, cart, bicycle, or horse.(a) harbour(b) hole(c) lift(d) roadThis question was posed to me in class test.My question is from Estimate of Earthwork by Three Methods in section Road Estimating, Sanitary and Water Supply Work of Civil Engineering Drawing

Answer»

The correct option is (d) road

The best explanation: Roads consist of one or two roadways (British English: CARRIAGEWAYS), each with one or more LANES and any associated sidewalks (British English: pavement) and road verges. In the Netherlands there is often a Protected Bicycle PATH provided for cycling.

Roads available for use by the public may be referred to as parkways, avenues, freeways, interstates, HIGHWAYS, or primary, secondary, and tertiary LOCAL roads.

45.

A _____________ houses the squatting pan or toilet seat and provides privacy and protection from the weather for the user.(a) roof(b) terrace(c) shade(d) shelterThis question was posed to me during an online interview.My doubt is from Design of Septic Tanks topic in chapter Road Estimating, Sanitary and Water Supply Work of Civil Engineering Drawing

Answer»

Correct option is (d) shelter

The best I can EXPLAIN: A shelter, shed, small building or “super-structure” HOUSES the squatting pan or toilet seat and provides PRIVACY and protection from the weather for the user. Ideally, the shelter or small building should have hand washing facilities available inside or on the outside (e.g. supplied with WATER from a rainwater harvesting tank on the roof of the shelter) although this is unfortunately rarely the case in practice. In the shelter, anal cleansing materials (e.g. toilet PAPER) and a solid waste bin should also be available. A more substantial structure may also be built, commonly known as an outhouse.

46.

A _________ is a type of toilet that collects human faeces in a hole in the ground.(a) gutter(b) septic tank(c) pit toilet(d) latrineThe question was posed to me in an internship interview.My question is taken from Design of Septic Tanks in portion Road Estimating, Sanitary and Water Supply Work of Civil Engineering Drawing

Answer»

Correct option is (c) pit toilet

Easiest explanation: A pit latrine or pit toilet is a TYPE of toilet that collects human faeces in a hole in the ground. They USE either no water or one to three litres per FLUSH with pour-flush pit latrines. When properly built and maintained they can decrease the spread of disease by reducing the amount of human faeces in the environment from open DEFECATION. This DECREASES the transfer of pathogens between faeces and food by flies.

47.

Road on the side of a cliff or mountain, with the ground rising on one side and falling away on the other is called _________(a) hill(b) corniche(c) cliff(d) coneThe question was asked during an online exam.This intriguing question originated from Estimate of Metalled Roads in division Road Estimating, Sanitary and Water Supply Work of Civil Engineering Drawing

Answer»

Right choice is (b) CORNICHE

Easiest EXPLANATION: A corniche is a road on the side of a cliff or mountain, with the ground rising on one side of the road and falling away on the other. The word COMES from the French ROUTE à corniche or “road on a ledge”.

48.

__________ forms the trackbed upon which railroad ties (sleepers) are laid.(a) Track ballast(b) Concrete ballast(c) Rail ballast(d) Wooden ballastI have been asked this question during a job interview.The above asked question is from Railway Line in division Road Estimating, Sanitary and Water Supply Work of Civil Engineering Drawing

Answer»

Right choice is (a) Track ballast

Best explanation: It is packed between, below, and around the ties. It is USED to bear the load from the railroad ties, to facilitate DRAINAGE of WATER, and also to keep down vegetation that might interfere with the track structure. This also SERVES to hold the track in place as the trains roll by. It is typically made of crushed stone, although ballast has sometimes consisted of other, less suitable materials, for example burnt clay. The TERM “ballast” comes from a nautical term for the stones used to stabilize a ship.

49.

Which type of trap is shown by the figure below?(a) S- trap(b) P- trap(c) Q-trap(d) R-trapThe question was asked in an interview for internship.My question is from Water Supply Works topic in chapter Road Estimating, Sanitary and Water Supply Work of Civil Engineering Drawing

Answer»

Right choice is (a) S- trap

The best I can explain: In domestic APPLICATIONS, traps are typically U, S, Q or J-shaped pipe located below or within a plumbing fixture. An S-shaped trap is also known as an S-bend. It was invented by ALEXANDER Cummings in 1775 but became known as the U-bend FOLLOWING the introduction of the U-shaped trap by Thomas Crapper in 1880. The new U-bend could not jam, so, unlike the S-bend, it did not need an overflow. The most COMMON of these traps in houses is referred to as a P-trap. It is the addition of a 90 degree fitting on the outlet side of a U-bend, thereby creating a P-like SHAPE.

50.

The pit is typically at least ____________ deep and ___________ across.(a) 14 meters, 10 m(b) 30 meters, 15 m(c) 3 meters, 1 m(d) 11 meters, 9 mThe question was posed to me by my college professor while I was bunking the class.This key question is from Design of Septic Tanks in portion Road Estimating, Sanitary and Water Supply Work of Civil Engineering Drawing

Answer»

Correct OPTION is (c) 3 meters, 1 m

Easiest explanation: The World Health ORGANIZATION recommends they be built a reasonable distance from the house balancing issues of easy ACCESS versus that of smell. The distance fromgroundwater and surface water should be as large as possible to decrease the risk of groundwater pollution. The hole in the slab should not be larger than 25 cm (9.8 inches) to prevent children falling in. LIGHT should be prevented from entering the pit to reduce access by flies. This may require the use of a lid to cover the hole in the floor when not in use.