A voltage source `V=V_(0) sin (100 t)` is connected to a black box in which there can be either one element out of `L,C,R` or any two of them connected in series. At steady state, the variation of current in the circuit and the source voltage are plotted together with time.using an oscilloscope, as shown The element (s) present in black box is/are: A. only `C`B. `L` and `C`C. `L` and `R`D. `R` and `C`

A voltage source `V=V_(0) sin (100 t)` is connected to a black box in

1.	A voltage source `V=V_(0) sin (100 t)` is connected to a black box in which there can be either one element out of `L,C,R` or any two of them connected in series. At steady state, the variation of current in the circuit and the source voltage are plotted together with time.using an oscilloscope, as shown The element (s) present in black box is/are: A. only `C`B. `L` and `C`C. `L` and `R`D. `R` and `C`
Answer» Correct Answer - D As current is leading the source voltage, so circuit should be capacitive in nature and as phase difference is not `pi/2`, it must contain resistor also.

Discussion

No Comment Found

Related InterviewSolutions

Can the phenomenon of resonance be exhibited in RL or RC circuit.
The impedance of a sereis `RL` circuit is same as the series `RC` circuit when connected to the same `AC` source separately keeping the same resistance. The frequency of the source isA. `(1)/(sqrt(LC))`B. `(1)/(2pi sqrt(LC))`C. `(R )/(L)`D. `(1)/(RC)`
The equation of an alternating voltage is `E = 220 sin (omega t + pi // 6)` and the equation of the current in the circuit is `I = 10 sin (omega t - pi // 6)`. Then the impedance of the circuit isA. 10 ohmB. 22 ohmC. 11 ohmD. 17 ohm
In an ac circuit, the current lags behind the voltage by `pi//3`. The components in the circuit areA. R and LB. R and CC. L and CD. Only R
In an ac circuit, the current lags behind the voltage by `pi//3`. The components in the circuit areA. R and LB. L and CC. R and CD. only R
A 200 km telephone wire has capacity of `0.014 muF km^(-1)`. If it carries an alternating current oif frequency 50kHz, what should be the value of an inductance required to be connected in series so that impedance is minimumn ?
In the circuit shown in figureure the `AC` source gives a voltage `V=20cos(2000t)`. Neglecting source resistance, the voltmeter and and ammeter readings will be .A. `0V,2.0A`B. `0V,1.4A`C. `5.6V,1.4A`D. `8V,2.0A`
A signal generator supplies a sine wave of `200V, 5kHz` to the circuit shown in the figureure. Then, choose the wrong statement. .A. The current in te resistive brance is `0.2 A`B. the current in the capacitive branch is `0.126 A`C. Total line current is `~~0.283A`D. Current in both the branches is same
In an `AC` circuit, the applied potential difference and the current flowing are given by `V=20sin100tvolt,I=5sin(100t-pi/2)` amp The power consumption is equal toA. `1000W`B. `40W`C. `20W`D. zero
In an `AC` circuit, the current is given by `i=5sin(100t-(pi)/2)` and the `AC` potential is `V=200sin(100t)`volt. Then the power consumption isA. `20` wattsB. `40` wattC. `1000` wattD. `0` watt

Discussion

No Comment Found

Related InterviewSolutions

Reply to Comment