Solve : New hard drive - cable select only??

1.	Solve : New hard drive - cable select only??
Answer» I have a NEW 80GB primary hard drive which I just installed, along with the 40GB secondary drive I've always had. The secondary drive, of course, is jumpered as the slave. When I first installed the new drive, I jumpered it as the master and installed XP with no apparent problems. But when I booted, I got an error message: BOOT DEVICE ERROR - INSERT SYSTEM DISK AND PRESS ANY KEY TO CONTINUE. After much gnashing of teeth, I finally discovered that the drive would only boot if it was jumpered to Cable Select. Is this unusual?What drive manuf. ? ? WD's in my experience need master with slave present or they get wonky... patio. The other thing i've seen is don't introduce any new drives after an OS install until you have done at least a 1/2 dozen or so cold boots. Quote What drive manuf. ? ? WD's in my experience need master with slave present or they get wonky... patio. The other thing i've seen is don't introduce any new drives after an OS install until you have done at least a 1/2 dozen or so cold boots. Primary - Western Digital 80GB Slave - Seagate 40GB THANKS, patio. The primary drive is the one I replaced; the slave was always there. I installed the OS on the primary and it went fine. But then it wouldn't boot, so I changed the jumpers from Master to Cable Select, and voila. Like you say, perhaps I should have DISCONNECTED the secondary and added it later. Switch ide cables i would advise w/d has also the option of a slave drive on it .....on the BACK of the drive which may.....mean remove the whit plastic jumper. Your main hard drive is seaching for the o/s system . of which the new h/d does not have it on.My computer: Primary - Western Digital 80GB Slave - Western Digital 40GB Works perfectly with 80-conductor cable and drives set to CS.Does not on dufs pc...........nothing new just like the owner........wally cartoons.........another wind-up by hoplessdufPatio, merlin, Commando: Thanks guys. That's good information. Quote My computer: Primary - Western Digital 80GB Slave - Western Digital 40GB Works perfectly with 80-conductor cable and drives set to CS. Right! 80-conductor cable is better anyway, as the second set of conductors are there as screens to prevent cross-talk between the other conductor wires, and the material which these wires are made of have less resistance than the older 40 wire cables. Less resistance = more conductivity and hence the passage of data along the wire is faster so you get an increase in overall performance. Every little bit helps. Quote Does not on dufs pc...........nothing new just like the owner........wally cartoons.........another wind-up by hoplessduf HUH ? ? patio.

Answer»

I have a NEW 80GB primary hard drive which I just installed, along with the 40GB secondary drive I've always had. The secondary drive, of course, is jumpered as the slave.

When I first installed the new drive, I jumpered it as the master and installed XP with no apparent problems. But when I booted, I got an error message: BOOT DEVICE ERROR - INSERT SYSTEM DISK AND PRESS ANY KEY TO CONTINUE. After much gnashing of teeth, I finally discovered that the drive would only boot if it was jumpered to Cable Select.

Is this unusual?What drive manuf. ? ?
WD's in my experience need master with slave present or they get wonky...

patio.

The other thing i've seen is don't introduce any new drives after an OS install until you have done at least a 1/2 dozen or so cold boots. Quote

What drive manuf. ? ?
WD's in my experience need master with slave present or they get wonky...

patio.

The other thing i've seen is don't introduce any new drives after an OS install until you have done at least a 1/2 dozen or so cold boots.

Primary - Western Digital 80GB
Slave - Seagate 40GB

THANKS, patio. The primary drive is the one I replaced; the slave was always there. I installed the OS on the primary and it went fine. But then it wouldn't boot, so I changed the jumpers from Master to Cable Select, and voila. Like you say, perhaps I should have DISCONNECTED the secondary and added it later.
Switch ide cables i would advise
w/d has also the option of a slave drive on it .....on the BACK of the drive which may.....mean remove the whit plastic jumper.

Your main hard drive is seaching for the o/s system .
of which the new h/d does not have it on.My computer:

Primary - Western Digital 80GB
Slave - Western Digital 40GB

Works perfectly with 80-conductor cable and drives set to CS.Does not on dufs pc...........nothing new just like the owner........wally cartoons.........another wind-up by hoplessdufPatio, merlin, Commando: Thanks guys. That's good information. Quote

My computer:

Primary - Western Digital 80GB
Slave - Western Digital 40GB

Works perfectly with 80-conductor cable and drives set to CS.

Right!

80-conductor cable is better anyway, as the second set of conductors are there as screens to prevent cross-talk between the other conductor wires, and the material which these wires are made of have less resistance than the older 40 wire cables.

Less resistance = more conductivity and hence the passage of data along the wire is faster so you get an increase in overall performance.

Every little bit helps. Quote

Does not on dufs pc...........nothing new just like the owner........wally cartoons.........another wind-up by hoplessduf

HUH ? ?

patio.

Solve : New hard drive - cable select only??

Discussion

No Comment Found

Related InterviewSolutions

Reply to Comment