The phenomena of the flowing of liquid towards the wall of tower and dispersed in lateral direction is called as?(a) Channeling(b) Flow casting(c) Entraining(d) RegimensI have been asked this question during an interview for a job.This is a very interesting question from Types of Random Packing in portion Packing Design and Operation of Distillation Design

The phenomena of the flowing of liquid towards the wall of tower and d

1.	The phenomena of the flowing of liquid towards the wall of tower and dispersed in lateral direction is called as?(a) Channeling(b) Flow casting(c) Entraining(d) RegimensI have been asked this question during an interview for a job.This is a very interesting question from Types of Random Packing in portion Packing Design and Operation of Distillation Design
Answer» RIGHT option is (a) CHANNELING For explanation I would say: This is called as channeling of LIQUID, such misdistribution is determined to a good gas liquid contact, therefore NECESSARY to collect liquid from wall and give it to BED again.

Discussion

No Comment Found

Related InterviewSolutions

Fs is denoted as?(a) Capacity parameter(b) Final storage(c) Full standup(d) Finishing StandupI got this question in unit test.This intriguing question comes from Packing Material in portion Packing Design and Operation of Distillation Design
The packing factor used to be taken as?(a) ap/e^3(b) ap/e^2(c) ap^2/e^2(d) ap^3/e^4I have been asked this question at a job interview.Enquiry is from Packing Material in portion Packing Design and Operation of Distillation Design
The shells are generally made of?(a) Copper(b) Iron(c) Wood(d) CeramicsI have been asked this question during an online interview.This question is from Packing Types and Objectives in section Packing Design and Operation of Distillation Design
Sluzer supply are of which three types?(a) AX,CX and CV(b) AY,BX and CX(c) AY,CX and BX(d) AX,BX and CYI got this question in an internship interview.I'm obligated to ask this question of Types of Random Packing topic in portion Packing Design and Operation of Distillation Design
For liquid and solid handling, that are corrosive the(a) Bubble tower is used(b) Venturi Scrubber is used(c) Spray tower is used(d) Agitated vessel are usedI have been asked this question during an online exam.This intriguing question originated from Packing Types and Objectives topic in portion Packing Design and Operation of Distillation Design
Minimum liquid rate for random packing is reported as?(a) 10-14 gpm/ft^2(b) 8-10 gpm/ft^2(c) 1-9 gpm/ft^2(d) 0.5-2 gpm/ft^2I have been asked this question in exam.I'd like to ask this question from Packing Material topic in division Packing Design and Operation of Distillation Design
The Height to Diameter ratio of CMR is?(a) 1:1(b) 1:3(c) 3:1(d) 1:5This question was addressed to me in an online quiz.This interesting question is from Types of Random Packing in division Packing Design and Operation of Distillation Design
Bubble columns, are used for?(a) Waste water treatment(b) Effluent treatment(c) Chlorine treatment(d) Sodium treatmentThe question was asked in a job interview.The question is from Packing Types and Objectives in portion Packing Design and Operation of Distillation Design
A layer of packing above the liquid distributor is called?(a) Dry packing(b) Wet packing(c) Can packing(d) Trump packingThe question was asked in homework.This intriguing question comes from Packing Material topic in portion Packing Design and Operation of Distillation Design
The Eckert chart contains a parameter FP which is called?(a) Pushing factor(b) Possibility factor(c) Praining factor(d) Packing factorThis question was addressed to me in homework.The above asked question is from Packing Material topic in portion Packing Design and Operation of Distillation Design

Discussion

No Comment Found

Related InterviewSolutions

Reply to Comment