What is the use of pre-emphasis?(a) to increase the signal to noise ratio for higher audio frequencies(b) to allow stereo audio to be carried by FM stations(c) to increase the signal to noise ratio for all audio frequencies(d) to increase the signal to noise ratio for lower audio frequenciesI had been asked this question in class test.This question is from Non Linear Device in section Side Band Techniques of Analog Communications

What is the use of pre-emphasis?(a) to increase the signal to noise ra

1.	What is the use of pre-emphasis?(a) to increase the signal to noise ratio for higher audio frequencies(b) to allow stereo audio to be carried by FM stations(c) to increase the signal to noise ratio for all audio frequencies(d) to increase the signal to noise ratio for lower audio frequenciesI had been asked this question in class test.This question is from Non Linear Device in section Side Band Techniques of Analog Communications
Answer» The correct choice is (d) to increase the SIGNAL to NOISE RATIO for lower AUDIO frequencies The best I can explain: Pre-emphasis is applied in communication systems to improve signal strength before transmission. It refers to boosting the amplitudes of the weak modulating voltages for HIGH audio frequencies. It is also helpful in increasing S/N ratio but for lower audio frequencies only.

Discussion

No Comment Found

Related InterviewSolutions

What is the modulation index of an AM signal if the peak voltage goes from Emax to Emin?(a) \(\frac{E_{min}}{E_{max}}\)(b) \(\frac{E_{max}}{E_{min}}\)(c) \(\frac{E_{max} – E_{min}}{E_{max} + E_{min}}\)(d) \(\frac{E_{max} + E_{min}}{E_{max} – E_{min}}\)This question was addressed to me during a job interview.My query is from Spectrum of AM SC Waves in section Side Band Techniques of Analog Communications
Which frequencies is produced if Vasin⁡(ωa t) amplitude modulates the carrier Vcsin⁡(ωc t)?(a) (ωc + ωa), (ωc – ωa) and ωc(b) (ωc) and (ωa)(c) (ωc + ωa) and (2ωc + 2ωa)(d) (2ωc) and (2ωa)I got this question in an online quiz.My query is from Spectrum of AM SC Waves in chapter Side Band Techniques of Analog Communications
What is the total sideband power if there is 100% modulation?(a) half the carrier wave(b) twice the carrier wave(c) equal to the carrier wave(d) one-fourth of the carrier waveI got this question in final exam.This interesting question is from Spectrum of AM SC Waves topic in portion Side Band Techniques of Analog Communications
If AM radio station increases its modulation index then there is an increase in receiving RF signal.(a) True(b) FalseI got this question in final exam.Origin of the question is Spectrum of AM SC Waves in section Side Band Techniques of Analog Communications
How an AM radio station increase its signal-to-noise ratio?(a) by increasing its modulation index(b) by decreasing its modulation index(c) by maintaining a constant modulation index(d) by increasing the frequencyThis question was addressed to me by my college professor while I was bunking the class.My question comes from Spectrum of AM SC Waves in section Side Band Techniques of Analog Communications
What is the main problem in using quadrature amplitude modulation?(a) high bandwidth is required(b) high power is required(c) incompability with ordinary AM radio waves(d) bandwidth required is lessI had been asked this question in class test.My enquiry is from Spectrum of AM SC Waves in section Side Band Techniques of Analog Communications
Only audio can be sent using Amplitude Modulation.(a) True(b) FalseI have been asked this question during an internship interview.The origin of the question is Chopper Circuit topic in division Side Band Techniques of Analog Communications
A single sideband modulation system requires a more complex demodulator circuit.(a) True(b) FalseThe question was posed to me during an online exam.Question is from Spectrum of AM SC Waves topic in chapter Side Band Techniques of Analog Communications
To demodulate a USB SSB signal, the receiver must ________(a) be set to USB mode(b) reinsert the carrier(c) be set to USB mode and reinsert the carrier(d) have low-fidelityThe question was asked by my college director while I was bunking the class.This interesting question is from Spectrum of AM SC Waves topic in chapter Side Band Techniques of Analog Communications
What is the full form of PEP in communication?(a) Peak Efficiency Power(b) Peak Envelope Power(c) Peak Efficiency Product(d) Peak Envelope PowerThe question was posed to me during an interview.This intriguing question originated from Chopper Circuit topic in division Side Band Techniques of Analog Communications

Discussion

No Comment Found

Related InterviewSolutions

Reply to Comment