Which of the following articles cannot be made from rolling?(a) Rails(b) Helmets(c) Bars(d) PlatesThe question was asked in homework.I'd like to ask this question from Hot Rolling topic in chapter Forming Process of Casting-Forming-Welding II

Which of the following articles cannot be made from rolling?(a) Rails(

1.	Which of the following articles cannot be made from rolling?(a) Rails(b) Helmets(c) Bars(d) PlatesThe question was asked in homework.I'd like to ask this question from Hot Rolling topic in chapter Forming Process of Casting-Forming-Welding II
Answer» Correct option is (b) Helmets To explain: Rolling is very useful for MAKING articles like bars, PLATES and rails, but it cannot be used for making helmets. For making helmets, DIFFERENT METHODS of casting are used.

Discussion

No Comment Found

Related InterviewSolutions

Fine blanking is a finishing operation in which shearing is done with very small clearances.(a) True(b) FalseI got this question during an online exam.This question is from Blanking and Piercing in division Forming Process of Casting-Forming-Welding II
When a metal is entering, how are the width and the length of the workpiece related to each other?(a) Direct relation(b) Inverse relation(c) Exponential relation(d) No relationI got this question in final exam.Asked question is from Flat Rolling in portion Forming Process of Casting-Forming-Welding II
Which of the following method is used for making crankshafts?(a) Drop forging(b) Press forging(c) Open die forging(d) Closed die forgingI have been asked this question by my school principal while I was bunking the class.The above asked question is from Drop and Press Forging in portion Forming Process of Casting-Forming-Welding II
In drop forging, the anvil is lighter than the hammer.(a) True(b) FalseThe question was asked in final exam.The query is from Drop and Press Forging topic in section Forming Process of Casting-Forming-Welding II
What increases when the take up reel rotates at a high speed?(a) Front tension(b) Above tension(c) Back tension(d) Beneath tensionThe question was asked in my homework.The above asked question is from Principle of Roll Pass in division Forming Process of Casting-Forming-Welding II
Which of the following cannot be regarded as an internal structure defect?(a) Edge crack(b) Zipper cracks(c) Alligatoring(d) QueveringI have been asked this question in an interview.My question is from Defects in Rolled Parts in portion Forming Process of Casting-Forming-Welding II
Drop forging is the most accurate form of forging.(a) True(b) FalseI have been asked this question during an online exam.This key question is from Drop and Press Forging topic in section Forming Process of Casting-Forming-Welding II
Which of the following defect occurs because of the bending of rolls?(a) Zipper cracks(b) Folds(c) Laminations(d) AlligatoringI got this question in an international level competition.Origin of the question is Defects in Rolled Parts topic in portion Forming Process of Casting-Forming-Welding II
The mechanical strength of the metal decreases due to the strain hardening of the metal.(a) True(b) FalseThe question was posed to me in an international level competition.I'd like to ask this question from Behaviour in Metal Forming in portion Forming Process of Casting-Forming-Welding II
For the minimum metal loss, the flash-less forging is better than the impression die forging.(a) True(b) FalseThe question was posed to me in an online interview.My query is from Classification of Metal Forming Processes in portion Forming Process of Casting-Forming-Welding II

Which of the following articles cannot be made from rolling?(a) Rails(b) Helmets(c) Bars(d) PlatesThe question was asked in homework.I'd like to ask this question from Hot Rolling topic in chapter Forming Process of Casting-Forming-Welding II

Discussion

No Comment Found

Related InterviewSolutions

Reply to Comment