Which of the following is the main advantage of using the centrifugal casting method?(a) Defects less casting(b) Maximum casting yield(c) Low cost(d) Fast production of castingsI got this question during an interview for a job.I need to ask this question from Advantages and Disadvantages of Casting topic in chapter Casting Process of Casting-Forming-Welding II

Which of the following is the main advantage of using the centrifugal

1.	Which of the following is the main advantage of using the centrifugal casting method?(a) Defects less casting(b) Maximum casting yield(c) Low cost(d) Fast production of castingsI got this question during an interview for a job.I need to ask this question from Advantages and Disadvantages of Casting topic in chapter Casting Process of Casting-Forming-Welding II
Answer» Correct answer is (b) Maximum casting yield The explanation: In centrifugal casting technique, there is no need for the gates and runners to be used in the process, which can save a lot of MOLTEN metal. This MAKES the increase in casting yield which can reach to the maximum that means negligible metal loss. And no cores are required during the process which makes this method very economical for the large SCALE production of CASTINGS.

Discussion

No Comment Found

Related InterviewSolutions

In the electron beam melting process, the kinetic energy is instantly converted into thermal energy.(a) True(b) FalseThe question was asked in an internship interview.Asked question is from Laser and Electron Beam Melting With Rapid Prototyping topic in chapter Casting Process of Casting-Forming-Welding II
Which of the following casting techniques is the best technique for casting tubes and hollow pipes?(a) Die casting(b) Slush casting(c) Centrifugal casting(d) Investment castingI had been asked this question by my school teacher while I was bunking the class.The above asked question is from Casting Techniques topic in chapter Casting Process of Casting-Forming-Welding II
The main purpose of electron beam melting is to build up the metal parts by layer forming.(a) True(b) FalseI had been asked this question by my college director while I was bunking the class.This intriguing question originated from Laser and Electron Beam Melting With Rapid Prototyping topic in division Casting Process of Casting-Forming-Welding II
In vacuum die casting, the melt enters into the mould cavity with less speed than that in the die casting technique.(a) True(b) FalseI have been asked this question during a job interview.Enquiry is from Casting Techniques topic in portion Casting Process of Casting-Forming-Welding II
The electron beam technology is not much efficient as compared to the laser technology used for manufacturing.(a) True(b) FalseThe question was asked in examination.Question is taken from Laser and Electron Beam Melting With Rapid Prototyping in portion Casting Process of Casting-Forming-Welding II
In Co2 moulding technique, the amount of water is zero percent in the sand mixture used for mould.(a) True(b) FalseThe question was asked during an interview.This intriguing question originated from Casting Techniques topic in chapter Casting Process of Casting-Forming-Welding II
The operations of fabrication in electron beam melting (EBM) are almost similar to that of laser beam melting (LBM).(a) True(b) FalseThe question was asked in my homework.My question is taken from Laser and Electron Beam Melting With Rapid Prototyping in chapter Casting Process of Casting-Forming-Welding II
In the gravity die casting technique, not every metal can be casted easily.(a) True(b) FalseThe question was posed to me in a national level competition.This intriguing question comes from Casting Techniques in section Casting Process of Casting-Forming-Welding II
High cost is the only main drawback of using the electron beam technology for the production of metal parts.(a) True(b) FalseThe question was posed to me during a job interview.Asked question is from Laser and Electron Beam Melting With Rapid Prototyping topic in chapter Casting Process of Casting-Forming-Welding II
In permanent mould casting method, metallic cores are mainly used instead of sand cores.(a) True(b) FalseI have been asked this question in class test.Origin of the question is Casting Techniques in division Casting Process of Casting-Forming-Welding II

Discussion

No Comment Found

Related InterviewSolutions

Reply to Comment