Which of the following is the main drawback of using the shell mould casting method?(a) Limited size of casting parts(b) High cost(c) Rough surface finish(d) Slow rate productionThe question was asked in unit test.The origin of the question is Advantages and Disadvantages of Casting in section Casting Process of Casting-Forming-Welding II

Which of the following is the main drawback of using the shell mould c

1.	Which of the following is the main drawback of using the shell mould casting method?(a) Limited size of casting parts(b) High cost(c) Rough surface finish(d) Slow rate productionThe question was asked in unit test.The origin of the question is Advantages and Disadvantages of Casting in section Casting Process of Casting-Forming-Welding II
Answer» Correct option is (a) Limited size of casting parts Easiest EXPLANATION: In SHELL moulding process, a dump box is used in which a heated metallic pattern is inserted with the sufficient amount of coating SAND, then the dump box is ROTATED by which the pattern has adhered to the coating sand and then the pattern is extracted out by melting. In this process, due to limited size of the dump box, only limited size of casting parts can be produced.

Discussion

No Comment Found

Related InterviewSolutions

In the electron beam melting process, the kinetic energy is instantly converted into thermal energy.(a) True(b) FalseThe question was asked in an internship interview.Asked question is from Laser and Electron Beam Melting With Rapid Prototyping topic in chapter Casting Process of Casting-Forming-Welding II
Which of the following casting techniques is the best technique for casting tubes and hollow pipes?(a) Die casting(b) Slush casting(c) Centrifugal casting(d) Investment castingI had been asked this question by my school teacher while I was bunking the class.The above asked question is from Casting Techniques topic in chapter Casting Process of Casting-Forming-Welding II
The main purpose of electron beam melting is to build up the metal parts by layer forming.(a) True(b) FalseI had been asked this question by my college director while I was bunking the class.This intriguing question originated from Laser and Electron Beam Melting With Rapid Prototyping topic in division Casting Process of Casting-Forming-Welding II
In vacuum die casting, the melt enters into the mould cavity with less speed than that in the die casting technique.(a) True(b) FalseI have been asked this question during a job interview.Enquiry is from Casting Techniques topic in portion Casting Process of Casting-Forming-Welding II
The electron beam technology is not much efficient as compared to the laser technology used for manufacturing.(a) True(b) FalseThe question was asked in examination.Question is taken from Laser and Electron Beam Melting With Rapid Prototyping in portion Casting Process of Casting-Forming-Welding II
In Co2 moulding technique, the amount of water is zero percent in the sand mixture used for mould.(a) True(b) FalseThe question was asked during an interview.This intriguing question originated from Casting Techniques topic in chapter Casting Process of Casting-Forming-Welding II
The operations of fabrication in electron beam melting (EBM) are almost similar to that of laser beam melting (LBM).(a) True(b) FalseThe question was asked in my homework.My question is taken from Laser and Electron Beam Melting With Rapid Prototyping in chapter Casting Process of Casting-Forming-Welding II
In the gravity die casting technique, not every metal can be casted easily.(a) True(b) FalseThe question was posed to me in a national level competition.This intriguing question comes from Casting Techniques in section Casting Process of Casting-Forming-Welding II
High cost is the only main drawback of using the electron beam technology for the production of metal parts.(a) True(b) FalseThe question was posed to me during a job interview.Asked question is from Laser and Electron Beam Melting With Rapid Prototyping topic in chapter Casting Process of Casting-Forming-Welding II
In permanent mould casting method, metallic cores are mainly used instead of sand cores.(a) True(b) FalseI have been asked this question in class test.Origin of the question is Casting Techniques in division Casting Process of Casting-Forming-Welding II

Discussion

No Comment Found

Related InterviewSolutions

Reply to Comment