The oil pressure used in lubricating the camshaft is ______ kpa.(a) 0-20(b) 20-40(c) 0-50(d) 50-100I got this question during an interview.My doubt is from Systems of Engine Lubrication topic in chapter Lubrication and Lubricants of Automotive Engine Design

The oil pressure used in lubricating the camshaft is ______ kpa.(a) 0-

1.	The oil pressure used in lubricating the camshaft is ______ kpa.(a) 0-20(b) 20-40(c) 0-50(d) 50-100I got this question during an interview.My doubt is from Systems of Engine Lubrication topic in chapter Lubrication and Lubricants of Automotive Engine Design
Answer» Right CHOICE is (d) 50-100 The best EXPLANATION: The oil pressure is maintained at 400-500kpa for the main and big-end bearing while about 50-100kpa pressure is USED for TIMING gears and camshaft bearing.

Discussion

No Comment Found

Related InterviewSolutions

What is the speed range of the rotor is usually in rpm in a centrifugal type oil filter?(a) 0-1000(b) 1000-2000(c) 2000-7000(d) 7000-10000I got this question by my college professor while I was bunking the class.This intriguing question comes from Lubrication and Lubricants in portion Lubrication and Lubricants of Automotive Engine Design
Which of the following is connected to a knob that operated manually helps in removing impurities on the disc peripheries in an edge type oil filter?(a) Brake(b) Clutch(c) Accelerator(d) ShaftThis question was posed to me during an interview.I would like to ask this question from Lubrication and Lubricants topic in division Lubrication and Lubricants of Automotive Engine Design
What is the range of maximum permissible resistance in a bar in a cartridge type oil filter?(a) 0(b) 1(c) 2(d) 5I got this question in semester exam.This intriguing question comes from Lubrication and Lubricants topic in section Lubrication and Lubricants of Automotive Engine Design
In what range is the accumulation of impurities increased concerning the operating time in an unfiltered system?(a) Not proportion(b) Proportional(c) Doesn’t depend(d) Has no effectThe question was asked during an online exam.This key question is from Lubrication and Lubricants in chapter Lubrication and Lubricants of Automotive Engine Design
Which is the most commonly used material for filtering in cartridge type oil filter?(a) Wire gauze(b) Copper(c) Cobalt(d) ZincThe question was posed to me during a job interview.My doubt is from Lubrication and Lubricants in portion Lubrication and Lubricants of Automotive Engine Design
Which among the following is provided in an edge type oil filter to remove the impurities periodically?(a) Central knob(b) Adjusting screw(c) Relief valve(d) Pilot jetThis question was posed to me in an interview for internship.The question is from Lubrication and Lubricants topic in section Lubrication and Lubricants of Automotive Engine Design
What is the resistance to flow in the range of bar offered by a new filter element?(a) 0-0.1(b) 0.1-0.3(c) 0.3-0.5(d) 0.5-0.7The question was posed to me by my college director while I was bunking the class.Asked question is from Lubrication and Lubricants topic in section Lubrication and Lubricants of Automotive Engine Design
Which of the following is also known as Edge type oil filter?(a) Stack(b) Plunger(c) Barrel(d) PistonThe question was asked by my school teacher while I was bunking the class.The question is from Lubrication and Lubricants topic in division Lubrication and Lubricants of Automotive Engine Design
On which side of the oil pump is the surface filter installed?(a) Inlet(b) Outlet(c) Transfer(d) IntermediateThis question was addressed to me in unit test.The query is from Lubrication and Lubricants topic in chapter Lubrication and Lubricants of Automotive Engine Design
Which of the following is not a good characteristic of an oil filter?(a) High filtration efficiency(b) Long life(c) Less pressure loss(d) Dirty exhaust fumesThe question was asked in quiz.Asked question is from Lubrication and Lubricants topic in section Lubrication and Lubricants of Automotive Engine Design

The oil pressure used in lubricating the camshaft is ______ kpa.(a) 0-20(b) 20-40(c) 0-50(d) 50-100I got this question during an interview.My doubt is from Systems of Engine Lubrication topic in chapter Lubrication and Lubricants of Automotive Engine Design

Discussion

No Comment Found

Related InterviewSolutions

Reply to Comment