What happens to the Electro discharge machining process under unfavourable working conditions?(a) Will remain stable(b) Explosion may occur(c) Machining rate increases(d) Nothing happensThis question was addressed to me during a job interview.My doubt is from EDM-Process Control, Automation, Environmental Impact in chapter Thermal Processes of Advanced Machining

What happens to the Electro discharge machining process under unfavour

1.	What happens to the Electro discharge machining process under unfavourable working conditions?(a) Will remain stable(b) Explosion may occur(c) Machining rate increases(d) Nothing happensThis question was addressed to me during a job interview.My doubt is from EDM-Process Control, Automation, Environmental Impact in chapter Thermal Processes of Advanced Machining
Answer» Correct choice is (B) Explosion may occur Explanation: Explosion occurs if Electro DISCHARGE machining is DONE under unfavourable process variables and CONDITIONS.

Discussion

No Comment Found

Related InterviewSolutions

What is the value of beam diameter that is obtained in IBM?(a) 1 cm(b) 3 cm(c) 5 cm(d) 7 cmThis question was posed to me in exam.Origin of the question is Ion Beam Machining-Introduction, Material Removal Rate topic in portion Thermal Processes of Advanced Machining
What are the values of tolerances obtained by using PBM?(a) ± 0.6 mm(b) ± 1.6 mm(c) ± 2.6 mm(d) ± 3.6 mmThe question was asked by my college director while I was bunking the class.I would like to ask this question from PBM topic in division Thermal Processes of Advanced Machining
The cut edge of the material tends to be __________ than the base metal in PBM.(a) Smoother(b) Harder(c) Same as(d) None of the mentionedThis question was posed to me in my homework.I need to ask this question from PBM in section Thermal Processes of Advanced Machining
What is the maximum value of the thickness used in PBM process?(a) 100 mm(b) 200 mm(c) 300 mm(d) 400 mmI have been asked this question by my college director while I was bunking the class.I'd like to ask this question from Plasma Beam Machining-Introduction And Machining system topic in chapter Thermal Processes of Advanced Machining
Which type of thin cast layer is produced when we use EBM?(a) Thin layer(b) Thick layer(c) No layer(d) All of the mentionedThe question was asked in exam.Query is from EBM-Applications, Advantages and Disadvantages topic in section Thermal Processes of Advanced Machining
Which of the following lenses are used for refocussing the electrons in EBM process?(a) Magnetic lens(b) Electronic lens(c) Magnetic & Electronic lens(d) None of the mentionedThis question was posed to me in a job interview.My question comes from Electronbeam Machining-Introduction, Equipment and Material removal topic in portion Thermal Processes of Advanced Machining
Which type of laser can be used for direct drilling or percussion?(a) Ruby laser(b) Nd-YAG laser(c) Ruby & Nd-YAG laser(d) None of the mentionedThe question was posed to me in an interview.This key question is from LBM-Applications in section Thermal Processes of Advanced Machining
Material removal rates which are about mg/pulse produces which type of holes?(a) Shallow(b) Deep(c) Very deep(d) All of the mentionedThis question was addressed to me in an interview.My query is from LBM-Applications in division Thermal Processes of Advanced Machining
Lasers of which type are used for modification of electronic components?(a) High power(b) Small spot size(c) Short pulse length(d) All of the mentionedI had been asked this question during an interview.I need to ask this question from LBM-Applications in section Thermal Processes of Advanced Machining
Which of the following are the process variables for texturing process in EDM?(a) Pulse current(b) Electrode polarity(c) Dielectric type(d) All of the mentionedI got this question during an internship interview.My question is from EDM-Applications in section Thermal Processes of Advanced Machining

Discussion

No Comment Found

Related InterviewSolutions

Reply to Comment