Which of the following is not a method to avoid piston slap?(a) Taper piston(b) Piston with T-slots(c) Offset piston(d) Increase the size of the piston skirtThe question was posed to me in examination.The above asked question is from Engine Components in division Basic Engine Components of Automotive Engine Design

Which of the following is not a method to avoid piston slap?(a) Taper

1.	Which of the following is not a method to avoid piston slap?(a) Taper piston(b) Piston with T-slots(c) Offset piston(d) Increase the size of the piston skirtThe question was posed to me in examination.The above asked question is from Engine Components in division Basic Engine Components of Automotive Engine Design
Answer» Correct choice is (d) Increase the size of the piston skirt To elaborate: The methods of reducing piston slap are the use of a vertical or T-slots, TAPER piston, cam ground piston, use of special ALLOYS, wire wound PISTONS, autothermic piston, bimetallic piston and offset piston whereas an increase in the piston skirt does not affect.

Discussion

No Comment Found

Related InterviewSolutions

Which of the following is also known as harmonic balancer?(a) Counterweight(b) Crank web(c) Vibration dampers(d) Main journalI got this question in a national level competition.Question is taken from Engine Components in portion Basic Engine Components of Automotive Engine Design
What is the percentage of carbon present in a cast steel type crankshaft?(a) 0-1(b) 2-4(c) 1.35-1.6(d) 4-6I got this question during an online exam.Query is from Engine Components in portion Basic Engine Components of Automotive Engine Design
How much is the ultimate tensile strength of the crankshaft material in MPa?(a) 400(b) 500(c) 600(d) 700This question was posed to me in my homework.My question comes from Engine Components in chapter Basic Engine Components of Automotive Engine Design
How many types of crankshaft construction are used universally?(a) 1(b) 2(c) 4(d) 6I have been asked this question by my school teacher while I was bunking the class.The doubt is from Engine Components in chapter Basic Engine Components of Automotive Engine Design
Which of the following is not a major part of the crankshaft?(a) Main journal(b) Crank pins(c) Water pump(d) Crank websThis question was addressed to me during an interview for a job.My doubt is from Engine Components in portion Basic Engine Components of Automotive Engine Design
Which of the following material is the most commonly used in the construction of crankshaft?(a) Cast steel(b) Bronze(c) Copper(d) leadThe question was asked in unit test.I'm obligated to ask this question of Engine Components topic in division Basic Engine Components of Automotive Engine Design
Which of the following acts as a damper in a belt-driven crankshaft?(a) Fulcrum(b) Rocker arm(c) Belt(d) StrainerThis question was posed to me in examination.The question is from Engine Components topic in portion Basic Engine Components of Automotive Engine Design
How much percentage of the cylinder bore size concerningthe thickness of the crank web?(a) 80(b) 60(c) 20(d) 40This question was posed to me at a job interview.My question is based upon Engine Components topic in chapter Basic Engine Components of Automotive Engine Design
Which of the following is termed as the escape of the gasses from the combustion chamber and entering into the crankshaft?(a) Scuffing(b) Piston slap(c) Buckling(d) Blow-byI had been asked this question by my school teacher while I was bunking the class.The doubt is from Engine Components in division Basic Engine Components of Automotive Engine Design
Which of the following helps in the uniform speed of crankshaft despite uneven power impulses of the engine cylinder?(a) Piston(b) Connecting rod(c) Gasket(d) FlywheelThis question was posed to me by my college professor while I was bunking the class.The question is from Engine Components in chapter Basic Engine Components of Automotive Engine Design

Discussion

No Comment Found

Related InterviewSolutions

Reply to Comment