Which of the following is the need of the gearbox?(a) To vary the speed of the vehicle(b) To vary the torque of the vehicle(c) To vary the power of the vehicle(d) To vary the acceleration of the vehicleThis question was posed to me in a job interview.Question is taken from Transmission System topic in chapter Chassis & Transmission System of Automobile Engineering

Which of the following is the need of the gearbox?(a) To vary the spee

1.	Which of the following is the need of the gearbox?(a) To vary the speed of the vehicle(b) To vary the torque of the vehicle(c) To vary the power of the vehicle(d) To vary the acceleration of the vehicleThis question was posed to me in a job interview.Question is taken from Transmission System topic in chapter Chassis & Transmission System of Automobile Engineering
Answer» The CORRECT option is (b) To vary the torque of the vehicle For explanation I WOULD SAY: The purpose of the gearbox is to give MEANS so that the torque can be varied as required between the engine and the road wheels.

Discussion

No Comment Found

Related InterviewSolutions

A two-piece propeller shaft requires one universal joint.(a) True(b) FalseI had been asked this question in unit test.My query is from Universal Joints and Differential topic in division Chassis & Transmission System of Automobile Engineering
The axes of the two shafts are intersecting and are at 35° to each other. These two shafts are connected by Hook’s joint. At which position of the drives shaft acceleration will be maximum?(a) 68.4°(b) 96.1°(c) 225.5°(d) 330.7°The question was asked in exam.I would like to ask this question from Universal Joints and Differential in division Chassis & Transmission System of Automobile Engineering
The axes of the two shafts are intersecting and are at 35° to each other. These two shafts are connected by Hook’s joint. At which position of the drives shaft velocity ratio will not be unity?(a) 42.145°(b) 222.145°(c) 317.85°(d) 141.52°I had been asked this question by my school principal while I was bunking the class.My question is taken from Universal Joints and Differential topic in chapter Chassis & Transmission System of Automobile Engineering
What is the need of the universal joint?(a) To change inclination(b) To bend sideways(c) To transfer torque at an angle(d) To change lengthI had been asked this question by my college director while I was bunking the class.Question is taken from Universal Joints and Differential topic in division Chassis & Transmission System of Automobile Engineering
The axes of the two shafts are intersecting and are at 30° to each other. These two shafts are connected by Hook’s joint. At which position of the drives shaft velocity ratio will be minimum?(a) 90°, 270°(b) 0°, 180°(c) 180°, 270°(d) 90°, 180°I have been asked this question in examination.Asked question is from Universal Joints and Differential topic in section Chassis & Transmission System of Automobile Engineering
Where is the differential located?(a) Between transmission and rear axle(b) Between engine and transmission(c) Between two propeller shaft(d) Between steering wheel and steering columnThis question was addressed to me in my homework.This interesting question is from Universal Joints and Differential in division Chassis & Transmission System of Automobile Engineering
Which types of joints are used when the shafts are inclined?(a) Universal joint(b) Hinge joint(c) Ball and socket joint(d) Pivot jointThis question was addressed to me in an interview for internship.My question is taken from Universal Joints and Differential in chapter Chassis & Transmission System of Automobile Engineering
In which of the configuration of epicyclic gearbox output will be forward and fast output speed?(a) Sun gear stationary, ring gear driven, planet carrier driving(b) Sun gear driving, ring gear driven, planet carrier stationary(c) Sun gear driven, ring gear stationary, planet carrier driving(d) Sun gear stationary, ring gear stationary, planet carrier drivingThis question was addressed to me by my school teacher while I was bunking the class.I'm obligated to ask this question of Transmission System topic in division Chassis & Transmission System of Automobile Engineering
Which types of gears are used in constant mesh gearbox?(a) Spur gear(b) Helical gear(c) Bevel gear(d) Worm gearI had been asked this question in an online quiz.My question is taken from Transmission System topic in section Chassis & Transmission System of Automobile Engineering
Which of the following is not part of automatic transmission?(a) Epicyclic gearbox(b) Torque convertor(c) Multi-plate clutch(d) Sliding mesh gearboxThis question was posed to me in final exam.My enquiry is from Transmission System in portion Chassis & Transmission System of Automobile Engineering

Discussion

No Comment Found

Related InterviewSolutions

Reply to Comment