How do you use a clinical thermometer and a laboratory thermometer?

1.	How do you use a clinical thermometer and a laboratory thermometer?
Answer» Clinical thermometer 1. Wash the clinical thermometer properly with an antiseptic solution. 2. To lower the mercury level, hold the thermometer firmly and give some jerks. 3. Ensure that it falls below 35°C. Now place the bulb of the thermometer under your tongue. 4. After one or two minutes, take the thermometer out and note the reading. 5. This is your body temperature. 6. Don’t hold the thermometer by the bulb while reading it. A Laboratory thermometer: 1. Take cold or hot water in a bowl. Place the mercury bulb of the thermometer in the water so that the bulb immerses in it. 2. Wait for some time till the mercury level shows a constant reading. 3. Note down that reading.

Answer»

Clinical thermometer

1. Wash the clinical thermometer properly with an antiseptic solution.

2. To lower the mercury level, hold the thermometer firmly and give some jerks.

3. Ensure that it falls below 35°C. Now place the bulb of the thermometer under your tongue.

4. After one or two minutes, take the thermometer out and note the reading.

5. This is your body temperature.

6. Don’t hold the thermometer by the bulb while reading it.

A Laboratory thermometer:

1. Take cold or hot water in a bowl. Place the mercury bulb of the thermometer in the water so that the bulb immerses in it.

2. Wait for some time till the mercury level shows a constant reading.

3. Note down that reading.

Discussion

No Comment Found

Related InterviewSolutions

Why are heaters fitted near the floor and air conditioners near the ceiling of a room?
Why are the Upper layers of water in a pond or a lake hotter than the lower layers during the hot summer?
In the arrangements A and B shown in Figure 4.7, pins P and Q are fixed to a metal loop and an iron rod with the help of wax. In which case are both the pins likely to fall at different times? Explain.
The heat energy required to raise the temperature of 20 kg of water from 25° C to 75° C. A) 103 cal B) 104 cal C) 105 cal D) 106 cal
Collect specific heats of various substances.
Calculate the two specific heats of nitrogen from the following data : `gamma = c_(p)//c_(v) = 1.51` density of nitrogen at N.T.P `= 1.234 g litre ^(-1)` and `J = 4.2 xx 10^(7) erg cal^(-1)`.
Calculate difference in specific heats for `1` gram of air at `N.T.P`. Given density of air at N.T.P. is `1.293 g litre^(-1), j=4.2xx10^(7)" erg "cal^(-1)`.
A vessel contains ice and is in thermal equilibrium at `-10^(@)C` and is supplied heat energy at the rate of 20 cal `s^(-1)` for 450 seconds. If the mass of ice is 0.1 kg and due to supply of heat energy, the whole ice just melts find the water equivalent of the vessel. (Take specific heat of ice `=0.5 cal g^(-1)""^(@)C^(-1)` and specific heat of the vessel is `=0.1 cal g^(-1)""^(@)C^(-1)`. Latent heat of fussion = `80 cal g^(-1)` and assume that no heat is transferred to the surroundings)
if specific heat capacity of mercury is 0.033 cal `g^(-1)" ".^(@)C^(-1)`, how much heat is gained by 0.05 kg of mercury when its temperature rises from `68^(@)F` to 313K?
Calculate the specific heat capacity at constant volume for a gas. Given specific heat capacity at constant pressure is `6.85 cal mol^(-1) K^(-1), R = 8.31 J mol^(-1)K^(-1)`. `J = 4.18 J cal^(-1)`.