i am new to this site and think i put this post in the wrong forum.Can anybody help with this?This is the first time i have built one.

I decided to try and build a com.i am using BIOSTAR A760G M2+ AM2+/AM2 AMD 760G Micro ATX AMD Motherboard...AMD Athlon 64 X2 6000+ Windsor 3.0GHz SOCKET AM2 125W Dual-Core Processor Model ADX6000CZBOX......OCZ SLI-Ready Edition 4GB (2 x 2GB) 240-Pin DDR2 SDRAM DDR2 800 (PC2 6400) Dual Channel Kit Desktop Memory Model OCZ2N800SR4GK.these 3 parts came as a package deal.when i turn on the system and i get a screen that says windows was not STARTED SUCCESSFULLY because of a power failure or it wasn't shut down correctly.on the same screen it gives you a few choices....to start in safe mode....runs windows normally and a couple other options.after not selecting any of those it goes to a blue screen and this is what it says:

A problem has been detected and windows has been shut down to prevent damage to your computer.
If this is the first time you have seen this stop error screen restart your computer.If this screens appears again follow these steps.

check for viruses on your computer.Removed any newly installed hard drive and drive controllers.Check your drive to make sure it is properly configured and terminated.
Run CHKDSK/F to check for hard drive corruption and then restart.

Technical Information
***SYOP 0x0000007b(0xBACC3528,0xc0000034,0x00000000,0x00000000)

When i put this all together and took my drive that has my xp on it(from the old com that i am using to write this)it said that windows was corrupted.I also get this message when i removed that drive.i get the same message when i try to load windows on the new drives and when i put in the disc with the drives on it that came with the mothboard.

I hope i gave enough info here and hopefully someone can save me.In case you need to know i have 2 1 TB drives,1 500GB drive and a 320GB drive in there now and none of them have windows on it.the 320 is the ata the other 3 are sata.
thank you for any and all help

I disconnected ata drives and tried to load windows on the sata drives and nothing happen.the same results when i try to load the drivers that come with the motherboardAre you trying to boot to the hard drive that was in the old computer? You will need to do a fresh install of windows. You cant swap in a hard drive that has windows on it and expect it to boot up.

Do you have a windows CD?I do have the os disc....i removed the ata drives and kept the 3 new sata drives in and when i put the os disc in nothing happens...these drives are new and there is nothing on them....when i turn the system on with the os disc in all that comes up is this on a black screen:
upper left corner of monitor:Hardware Monitor....
CPU Temp :24C CPU Fan :2848 RPM System Fan :N/A
CPU Voltage :1.376V Chip Voltage :1.120V +3.30V :3.376V
+12.0V :12.224V DDR Voltage :1.920V HT Voltage 1.136V
5VSB 5.107VDo you have the CD drive set as the first boot device?

Do other bootable CDs work?

What happens if you disconnect all of the hard drives and try to boot to the CD?I have the dvd/cd as the first boot device,but it seems that every time i go back into it i need to set it as the first one again.System always set the floppy(which i don't have)as the first one.The only other cd i tried other than windows was the driver cd that came with the board.When i unhook all drives i get the same as you see below,but if i hit ctl+alt+del nothing happens.usually it would restart the unit

I have 3 brand new sata drives in the unit.i have tried to go to the bios screen and "load optimal defaults" then on reboot selected the dvd/cd as a boot device and all i got was this

upper left corner of monitor:Hardware Monitor....
CPU Temp :24C CPU Fan :2848 RPM System Fan :N/A
CPU Voltage :1.376V Chip Voltage :1.120V +3.30V :3.376V
+12.0V :12.224V DDR Voltage :1.920V HT Voltage 1.136V
5VSB 5.107V
is it possible the board is bad?the whole time i have turn this system on i never heard any beeps coming from it.this is a vew dvd/cd...does that matter? Quote from: sammic on September 16, 2009, 05:05:09 AM

I have the dvd/cd as the first boot device,but it seems that every time i go back into it i need to set it as the first one again.System always set the floppy(which i don't have)as the first one.

This points to a dead/dying battery... or no battery at all.

got a new vista now getting these errors
these are the errors i am getting trying to load vista
Process1_ Initialization_Failed 0x0000006B

irql_not_less_or_equal

buzz are you using vista on it?