The ratio of the length of the drawing of the object to the actual length of the object is called ___________(a) Resulting fraction(b) Representative figure(c) Representative fraction(d) Representative indexThe question was posed to me in exam.The above asked question is from Scales topic in portion Lettering Practice, Scales & Curves of Civil Engineering Drawing

The ratio of the length of the drawing of the object to the actual len

1.	The ratio of the length of the drawing of the object to the actual length of the object is called ___________(a) Resulting fraction(b) Representative figure(c) Representative fraction(d) Representative indexThe question was posed to me in exam.The above asked question is from Scales topic in portion Lettering Practice, Scales & Curves of Civil Engineering Drawing
Answer» The correct option is (c) Representative fraction Easiest explanation: Representative fractions are a UNIT-less relation between one “unit” on the map and however many “units” of the same type on the ground. When a 1 cm long line in a drawing SHEET represents 1 m length of the ACTUAL object on the ground, the R.F is equal to 1 cm/1 m = 1/100. These are of 3 types-full SCALE, reduced scale and ENLARGED scale.

Discussion

No Comment Found

Related InterviewSolutions

Which of the following is not true regarding concentric and eccentric circles?(a) Concentric circles have a common centre point(b) Eccentric circles have no common centre point(c) Concentric circles have no common centre point(d) Two or more circles with a common centre point are called concentricI had been asked this question in final exam.Enquiry is from Curves Used in Engineering Practice topic in section Lettering Practice, Scales & Curves of Civil Engineering Drawing
The angle bisector bisects the angle exactly __________(a) Perpendicular(b) 60 degree(c) Half(d) Any ratioThis question was addressed to me in exam.My question is from Geometrical Construction topic in division Lettering Practice, Scales & Curves of Civil Engineering Drawing
In lettering ‘A’ the height of capital letter is divided in how many parts?(a) 10(b) 14(c) 16(d) 8This question was posed to me by my college director while I was bunking the class.The question is from Lines, Lettering and Dimensioning in chapter Lettering Practice, Scales & Curves of Civil Engineering Drawing
Which grade of pencil is used for drawing arrowheads?(a) 2H(b) 2B(c) 7H(d) HThis question was addressed to me in homework.My doubt is from Lines, Lettering and Dimensioning topic in portion Lettering Practice, Scales & Curves of Civil Engineering Drawing
For all value of the co-ordinates of a moving point Pare (a cos θ, b sin θ); what will be the equation to the locus of P?(a) x^2/a^2 +y^2/b^2 = 0(b) x^2/b^2 +y^2/a^2 = 0(c) x^2/b^2 +y^2/a^2 = 1(d) x^2/a^2 +y^2/b^2 = 1I had been asked this question during an online interview.I need to ask this question from Loci of Points topic in chapter Lettering Practice, Scales & Curves of Civil Engineering Drawing
When the point is within the circle, the curve is called an ________(a) Inferior trochoid(b) Superior trochoid(c) Inscribed trochoid(d) Superior trochiodThe question was posed to me in quiz.My question is from Curves Used in Engineering Practice in chapter Lettering Practice, Scales & Curves of Civil Engineering Drawing
Vernier scale consists of two important parts, vernier scale and _________(a) Secondary scale(b) Initial scale(c) Main scale(d) Large scaleThis question was posed to me by my school teacher while I was bunking the class.This intriguing question originated from Scales in division Lettering Practice, Scales & Curves of Civil Engineering Drawing
Which type is the line A in the following figure?(a) Dimension line(b) Extension line(c) Centre line(d) Short-break lineThis question was addressed to me in an online quiz.The doubt is from Lines, Lettering and Dimensioning topic in chapter Lettering Practice, Scales & Curves of Civil Engineering Drawing
Figure below represents a section (shaded) obtained due to intersection by a plane that is parallel to the axes of the cones, what it the section called?(a) Parabola(b) Hyperbola(c) Ellipse(d) CycloidThis question was addressed to me during an online interview.Enquiry is from Curves Used in Engineering Practice topic in division Lettering Practice, Scales & Curves of Civil Engineering Drawing
What does the “Single-Stroke” lettering mean?(a) Cursive writing(b) Uniformity in letters as obtained in one stroke of the pencil(c) Writing in one stroke without lifting the pencil(d) Writing only with hard, small diameter lead-pencilThis question was posed to me by my school teacher while I was bunking the class.My doubt stems from Lines, Lettering and Dimensioning in section Lettering Practice, Scales & Curves of Civil Engineering Drawing

Discussion

No Comment Found

Related InterviewSolutions

Reply to Comment