Name the type of pointing, where mortar is pressed hard in the raked joints and by finishing off flush with the edge of masonry units. The edges are neatly trimmed with trowel and straight edge.(a) Struck pointing(b) V-pointing(c) Weathered pointing(d) Flush pointingThe question was asked during an internship interview.Enquiry is from Analysis of Rates of Plastering and Pointing in portion Analysis of Rates of Civil Engineering Drawing

Name the type of pointing, where mortar is pressed hard in the raked j

1.	Name the type of pointing, where mortar is pressed hard in the raked joints and by finishing off flush with the edge of masonry units. The edges are neatly trimmed with trowel and straight edge.(a) Struck pointing(b) V-pointing(c) Weathered pointing(d) Flush pointingThe question was asked during an internship interview.Enquiry is from Analysis of Rates of Plastering and Pointing in portion Analysis of Rates of Civil Engineering Drawing
Answer» CORRECT option is (d) Flush POINTING Easy EXPLANATION: It does not give good appearance. But, flush pointing is more durable because of resisting the PROVISION of space for dust, water etc., due to this reason, flush pointing is extensively used.

Discussion

No Comment Found

Related InterviewSolutions

Three main types of concrete pavements commonly used are Jointed plain concrete pavement (JPCP), ___________________ and continuously reinforced concrete pavements (CRCP).(a) Jointed reinforced concrete pavement (JRCP)(b) Jointed reinforced pavement (JRP)(c) Jointed concrete pavement (JCP)(d) Reinforced concrete pavement (RCP)The question was posed to me during a job interview.Enquiry is from Analysis of Rate of Road Work topic in section Analysis of Rates of Civil Engineering Drawing
For 2.5 cm thick c.c. floor of 1:2:4 proportion, for 100 sq m, what amount of stone aggregate will be required?(a) 5.20 cu m(b) 1.20 cu m(c) 2.40 cu m(d) .20 cu mI have been asked this question in an internship interview.This intriguing question comes from Analysis of Rates of Cement Concrete in chapter Analysis of Rates of Civil Engineering Drawing
For a four layer flexible pavement, there is a surface course, base course, and ______________ constructed over a compacted, natural soil subgrade.(a) sub-grade course(b) sub-base course(c) base course(d) sub-ballastThis question was addressed to me during an interview.I want to ask this question from Analysis of Rate of Road Work topic in section Analysis of Rates of Civil Engineering Drawing
Concrete is strong in tension but weak in compression.(a) True(b) FalseI had been asked this question in a job interview.This question is from Analysis of Rates of Cement Concrete in section Analysis of Rates of Civil Engineering Drawing
______________ include general office expenses, rents, taxes, supervision and other costs which are indirect expenses and not productive expenses on the job.(a) Total costs(b) General costs(c) Overhead costs(d) ContingenciesI got this question during an interview for a job.I need to ask this question from Estimation of Basic Rates Occurred in chapter Analysis of Rates of Civil Engineering Drawing
Instead of plastering entire surface of the masonry, special mortar finishing work is done to the exposed joints. This is called pointing.(a) True(b) FalseI got this question during an online interview.My doubt is from Analysis of Rates of Plastering and Pointing in division Analysis of Rates of Civil Engineering Drawing
The following figure is a rubbed, keyed or grooved type of pointing.(a) True(b) FalseI got this question by my school teacher while I was bunking the class.This intriguing question comes from Analysis of Rates of Plastering and Pointing topic in division Analysis of Rates of Civil Engineering Drawing
Cracks in plastering may be caused by settlement of the building, by the use of inferior materials or by bad workmanship.(a) True(b) FalseThe question was posed to me at a job interview.Origin of the question is Analysis of Rates of Plastering and Pointing in section Analysis of Rates of Civil Engineering Drawing
The United States has the largest network of roads of any country with 4,050,717 miles (6,518,997 km) as of 2009.(a) False(b) TrueI got this question in a job interview.This interesting question is from Analysis of Rate of Road Work in division Analysis of Rates of Civil Engineering Drawing
___________ of building is the useful area or liveable area or lettable area. This is the total floor area minus the circulation area, verandahs, corridors, passages, staircase, lifts, entrance hall, etc. minus other non-useable areas.(a) Plinth area(b) Floor area(c) Carpet area(d) Circulation areaThe question was posed to me in quiz.Question is taken from Estimation of Basic Rates Occurred topic in division Analysis of Rates of Civil Engineering Drawing

Discussion

No Comment Found

Related InterviewSolutions

Reply to Comment