When an area is symmetrical about both its axes, the centre of gravity will be at the __________ of these axes.(a) linear point(b) different point(c) collinear point(d) point of intersectionThe question was posed to me in an online quiz.Query is from Centres of Gravity and Moments of Inertia of Area topic in section Development of Surfaces, Isometric Projections, Perspective Projections & Transformation of Projections of Civil Engineering Drawing

When an area is symmetrical about both its axes, the centre of gravity

1.	When an area is symmetrical about both its axes, the centre of gravity will be at the __________ of these axes.(a) linear point(b) different point(c) collinear point(d) point of intersectionThe question was posed to me in an online quiz.Query is from Centres of Gravity and Moments of Inertia of Area topic in section Development of Surfaces, Isometric Projections, Perspective Projections & Transformation of Projections of Civil Engineering Drawing
Answer» Correct choice is (d) point of INTERSECTION Explanation: SET the two equations for y equal to each other. SOLVE for x. This will be the x-coordinate for the point of intersection. Use this x-coordinate and PLUG it into either of the original equations for the lines and solve for y.

Discussion

No Comment Found

Related InterviewSolutions

These are points at which the edges of the object appear to be converging. This point is seen at eye level, ie. on HP are __________(a) Station point(b) Piercing point(c) Exit point(d) Vanishing pointI had been asked this question in an interview for job.My question comes from Perspective Projection in division Development of Surfaces, Isometric Projections, Perspective Projections & Transformation of Projections of Civil Engineering Drawing
The shape of isometric drawing will be ______________(a) a plus(b) a cuboid(c) a staircase(d) a triangular prismI had been asked this question in a national level competition.This interesting question is from Isometric Projection in section Development of Surfaces, Isometric Projections, Perspective Projections & Transformation of Projections of Civil Engineering Drawing
The isometric view of the figure will resemble what type of structure?(a) A chair(b) A staircase(c) A table(d) A columnThis question was posed to me in examination.My enquiry is from Isometric Projection in chapter Development of Surfaces, Isometric Projections, Perspective Projections & Transformation of Projections of Civil Engineering Drawing
The following figure shows the _________ view of an object.(a) oblique(b) isometric(c) orthographic(d) perspectiveThe question was asked at a job interview.The origin of the question is Isometric Projection in chapter Development of Surfaces, Isometric Projections, Perspective Projections & Transformation of Projections of Civil Engineering Drawing
The red, blue curve in the figure (shown below) represents __________(a) welding(b) joining(c) fitting(d) curve of intersectionI got this question by my school teacher while I was bunking the class.This intriguing question comes from Intersection of Surfaces in portion Development of Surfaces, Isometric Projections, Perspective Projections & Transformation of Projections of Civil Engineering Drawing
The figure below represents _____________ point perspective.(a) 2(b) 3(c) 4(d) 5I had been asked this question by my school teacher while I was bunking the class.The doubt is from Oblique Projection in portion Development of Surfaces, Isometric Projections, Perspective Projections & Transformation of Projections of Civil Engineering Drawing
Here which type of isometric drawing view does the figure represents?(a) 3-Dimensional(b) Top, Front and Side(c) Multi-view drawing(d) OrthographicThe question was posed to me by my school teacher while I was bunking the class.The question is from Isometric Projection in division Development of Surfaces, Isometric Projections, Perspective Projections & Transformation of Projections of Civil Engineering Drawing
In perspective projection, all lines of sight start at a ________ point.(a) double(b) triple(c) multiple(d) singleI had been asked this question during an online interview.My question comes from Perspective Projection topic in section Development of Surfaces, Isometric Projections, Perspective Projections & Transformation of Projections of Civil Engineering Drawing
When the receding lines are true length, and the projectors are at 45 degrees to the plane of projection, the oblique drawing is called ______________(a) oblique projection(b) isometric projection(c) axonometric projection(d) cavalier projectionI have been asked this question by my school principal while I was bunking the class.The question is from Oblique Projection topic in chapter Development of Surfaces, Isometric Projections, Perspective Projections & Transformation of Projections of Civil Engineering Drawing
Figure below shows isometric view of the object having____________(a) irregular curve(b) circular curve(c) inclined curve(d) isometric curveThis question was addressed to me in examination.This key question is from Isometric Projection in portion Development of Surfaces, Isometric Projections, Perspective Projections & Transformation of Projections of Civil Engineering Drawing

Discussion

No Comment Found

Related InterviewSolutions

Reply to Comment